Showing 72 results for Sorption
S Dehestaniathar, Sh Amini, A Maleki, B Shahmoradi, N Reshadmanesh, P Teymouri,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objectives: Fluoride has both beneficial and detrimental effects on health. Therefore, it is important to determine its concentration in drinking water. Dental fluorosis and skeletal fluorosis are health effects caused by long term exposure to high levels of fluoride in drinking water. The aim of this research was to investigate fluoride removal using modified diatomite-supported ferric oxide nanoparticles and to determine the adsorption kinetics and isotherm.
Materials and Methods: This fundamental and practical study was performed at laboratory scale. The effects of pH (3.5-9.5), contact time (20-100 min), adsorbent dosage (1-5 g/L), and initial concentrations of fluoride (5-25 mg/L) on the adsorption efficiency were evaluated. The properties of adsorbent were investigated using XRD, XRF, FTIR and FESEM. Finally, the suitability of pseudo first and second order kinetics, and Langmuir and Freundlich isotherms for the data were investigated.
Results: This study showed that the removal efficiency of F- increased with increase in contact time, decrease in pH, increase in adsorbent dose, and increase in initial fluoride concentration. The highest removal efficiency was observed at pH=3.5, 60 minutes contact time, and 3 g/L of adsorbent dose in the initial concentration of 5 mg/L F-. Pseudo first order and Freundlich were the best fitted kinetic and isotherm models, respectively, for describing F- adsorption process.
Conclusion: The present study indicates that the modified diatomite-supported ferric oxide nanoparticles can be used as an effective and environmentally friendly biosorbent for the removal of fluoride ions from aqueous solutions.
Z Rahmani, M Harati, Mr Rahmani, Y Poureshgh, Mt Samadi,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objective: Surfactants can be found in soaps, detergents, pharmaceutical products, personal care products, as well as in leather industries. In this study, adsorption of Sodium Dodecyl Sulfate (SDS) on magnetic multi-walled carbon nanotubes in the aqueous solutions was investigated.
Materials and methods: Surfactant concentration, adsorbent dosage, and pH values were considered as variables. Residual surfactant was measured using methylene blue method and adsorbent characteristic was determined by X-Ray diffraction and Fourier transform infrared spectroscopic analysis. Adsorption capacity, adsorption isotherm, and kinetic reaction were also investigated.
Results: Adsorption investigations demonstrated that the increase in initial SDS concentration or pH values, led to the decrease in SDS adsorption. Conversely, the same result was achieved by decreasing adsorbent dosage. After 120 min SDS adsorption became stable. By increasing in SDS concentration from 15 to 150 mg/L, adsorption capacity improved from 8 to 61 mg/g. Isotherm and kinetic data demonstrated that experimental data pursued Langmuir isotherm (R2=0.993) and pseudo-second order equation (R2=0.992).
Conclusion: Magnetic multiwall carbon nanotubes can be used as an effective and useful sorbent for SDS removal due to several advantages including: high adsorption capacity, relatively low equilibrium time, and easy separation of magnetic multiwall carbon nanotubes from aqueous solutions.
M Nourinejad, N Arsalani, H Namazi,
Volume 10, Issue 1 (6-2017)
Abstract
Background and Objective: Nicotine as the most toxic alkaloid in tobacco is one of the compounds which causes human death over the past few decades. The purpose of this paper was to remove nicotine environmental pollution from aqueous solutions using halloysite-polythiophene nanocomposite.
Materials and Methods: Halloysite-polythiophene nanocomposite was prepared using a homogeneous solution of HNT and FeCl3 at 0-5°C by the ball milling technique. In this study, parameters such as pH, contact time and initial concentration of nicotine in laboratory scale were studied and the physical properties of the adsorbent were characterized via fourier transform infrared (FTIR) and scanning electron microscopy (SEM). Then, the absorption results were described using Langmuir and Freundlich isotherms.
Results: The results showed that the pH, initial concentration of nicotine and contact time had a direct effect on the nicotine adsorption process. The adsorption of nicotine followed Langmuir isotherm (R2 < 0/995). Moreover, the best adsorption result was achieved at pH=7, 50mg adsorbent, contact time of 90 min and 50mg/L of nicotine.
Conclusion: The results of this study showed that the Halloysite modification as a mineral composite with polythiophene and the synthesis of HNT@PTh nanocomposite can be used as an effective adsorbent to adsorb the nicotine.
Y Azimzadeh, N Najafi, A Reyhanitabar, Sh Oustan,
Volume 10, Issue 1 (6-2017)
Abstract
Background and Objective: Phosphorus (P), as one of the agricultural, industrial and urban wastewater pollutants, plays an important role in eutrophication of surface waters. Use of cationic sorbents for removal of anions including phosphate from aqueous environments is a well-known and effective method. Meanwhile, layered double hydroxides (LDHs) are known as effective anion exchange sorbents. In this study, the efficiency of Mg-Al layered double hydroxide (Mg-Al-LDH) for P removal from aqueous solutions was investigated.
Methods and Materials: The Mg-Al layered double hydroxide (Mg-Al-LDH) was synthesized by co-precipitation method and used for removing of P from aqueous solutions. The kinetics and equilibrium studies of phosphate adsorption by Mg-Al-LDH were performed using a batch experiment at different contact times, initial phosphate concentrations, pH values, ionic strengths and doses of sorbent.
Results: The results of the kinetics experiments showed that sorption of P with LDH reached equilibrium after 30 min. The highest correlation coefficient was obtained for the pseudo-second order model, indicated that chemical sorption controlled the rate of phosphate sorption by LDH. The results showed that the sorption experiments data were in good agreement with Langmuir model and the maximum adsorption capacity predicted by this model was 37.83 mg P/g LDH.
Conclusion: The current study revealed that P adsorption by LDH was increased by increasing contact time and concentration of LDH, but decreased by increasing initial concentration of P, pH and ionic strength. The optimum conditions for phosphate anion adsorption by Mg-Al-LDH were determined as P initial concentration of 20 mg/L, contact time of 120 min, pH of 3.0, sorbent dose of 10 g/L and ionic strength of 0.03 mol/L.
P Baratpour, G Moussavi, A Alahabadi, E Fathi, S Shekoohiyan,
Volume 10, Issue 2 (9-2017)
Abstract
Background and Objective: With industrial development and population growth, the emerging contaminants enter into the natural water resources. Therefore, adsorption potential of Ammonium Chloride-induced activated carbon (NAC) to remove metolachlor pesticide from contaminated water was investigated in this study.
Materials and Methods: The effects of operational conditions including solution pH, NAC concentration, metolachlor initial concentration and contact time on the removal of metolachlor by Ammonium Chloride-induced activated carbon (NAC) and standard activated carbon (SAC) were studied.
Results: Over 92.4% of 50 mg/L metolachlor was adsorbed using 0.3 g NAC/L within 5 min, and by increasing the reaction time to 60 min the removal efficiency reached to 100%. Under similar experimental conditions, standard activated carbon (SAC) could only adsorb 20% of metolachlor within 5 min and increase of contact time to 40 min caused the improvement of metolachlor adsorption onto SAC to 48%. The adsorption onto SAC was not influenced by the contact time over 40 min. Kinetic analysis showed that experimental adsorption data for both NAC and SAC were best fitted to the pseudo-second-order model. The maximum adsorption capacities of metolachlor onto NAC and SAC calculated by the Langmuir model were 344.8 and 238.1 mg/g, respectively.
Conclusion: Generally, these results showed that developed NAC was an efficient adsorbent with high removal efficiency for eliminating the halogenated pesticides from the contaminated water streams.
H Kamani, Ah Panahi, Sd Ashrafi, F Kord Mostafapour, Ns Omrani Gargari,
Volume 10, Issue 3 (12-2017)
Abstract
Background and Objective: Extreme use of antibiotics and discharging to the environment lead to serious consequences. Mesoporous silica such as MCM-41 material is widely used to absorb contaminants from the aqueous solution. The aim of this study was to evaluate mesoporous synthesis of MCM-41 and its efficacy for removal of the antibiotic cephalexin from aqueous solution.
Materials and Methods: Physical characteristics and absorbent structure synthesized by techniques BET, FTIR and XRD were analyzed. The effect of variables such as pH values (3, 7, 11), the dose of MCM-41 (200, 500, 800 mg/L), initial concentration of cephalexin (50, 75, 100 mg/L), contact time (30, 60, 90 min), and process temperature (20, 30, 40 0C) on absorption of cephalexin were studied. In order to achieve the optimal experimental conditions, response surface methodology (RSM) model was used.
Results: The results showed that pH (p=0.0001), adsorbent dose (p=0.0001), initial concentration of cephalexin (p=0.0001), contact time (p=0.01), pH2 (p=0.0002) and pH (p=0.04) and initial concentration had a significant impact on the response variable. The optimum removal condition based on analysis of variance and the model was at the reaction time 90 min, pH 3, initial concentration 50 mg/L and adsorption dose 600 mg/L. Under these conditions, the removal efficiency of 81.1% was achieved.
Conclusion: The results showed that adsorption process with the mesoporous MCM-41 had a high efficiency on the removal of cephalexin from the aqueous environments.
M Ghodrat, E Asrari,
Volume 10, Issue 4 (3-2018)
Abstract
Background and Objective: Excessive consumption of antibiotics and the entrance of the potentially hazardous substances to the environment has become one of the environmental concerns. Today, adsorption is one of the efficient and reliable methods for the removal of this class of compounds. The aim of this study was to synthesize chitosan-Fe3O4 and to compare the efficacy of removing erythromycin antibiotics from aqueous humorous media by this adsorbent and chitosan.
Materials and Methods: The structural properties of the synthesized adsorbent were analyzed by TEM, PSA, VSM techniques. Various parameters including pH (1-11), contact time (0-60 min), adsorbent concentration (1-5 g/L), and initial concentrations of erythromycin (5-50 mg/L) was evaluated for the removal efficiency. For data analysis, Excel software was used. The equilibrium constant and the kinetic constants were calculated from the first-order kinetic model using Freundlich and Langmuir isotherms.
Results: The results indicated that increased pH and initial concentration of erythromycin increased the dose of adsorbents and the contact time of removal efficiency. The highest absorption efficiency at pH of 3 for both adsorbents, the contact time 30 min for modified chitosan and 50 min for chitosan, the dose of adsorbent 2 g/L for modified chitosan, and 3 g/L for chitosan and the initial concentration of erythromycin for each of the two adsorbents was 10 mg/L and the erythromycin adsorption by both adsorbents follows the Langmuir isotherm and the pseudo second order kinetics.
Conclusion: According to these results, chitosan modified with Fe3O4 can be used as a more effective adsorbent than chitosan for removal of erythromycin by adsorption method.
N Rouniasi, Sm Monavari, Ma Abdoli, M Baghdadi, A Karbasi,
Volume 11, Issue 2 (9-2018)
Abstract
Background and Objective: Water pollution due to heavy metals is a critical and increasing problem worldwide. In this study, removal of cadmium and lead heavy metals using a graphene oxide (GO) adsorbent was examined.
Materials and Methods: GO nanosheets were synthesized through Hummer’s method, and its characterizations were examined using FTIR, XRD, and SEM. The effect of independent variables pH, contact time and initial concentration of the solution on removal efficiency of Cd2+and Pb2+ using response surface methodology was evaluated according to Box-Behnken experimental design. Applying quadratic model, adsorption rate of Cd2+ and Pb2+ achieved 99%. ANOVA was applied for statistical analysis of responses.
Results: According to SEM images, the average size of graphene oxide sheets was 1 to 3 µm. After optimization through RSM, the adsorption capacity for Pb2+ and Cd2+ was 136 mg/g and 68 mg/g, respectively. Examination of the isotherms suggested that Cd2+ and Pb2+ adsorption follows Langmuir and Freundlich isotherm, respectively.
Conclusion: the results show that the graphene oxide performed well in removing both Cd2+ and Pb2+ ions from aqueous solutions. The most influential parameters on the above-mentioned heavy metals adsorption were pH of the solution and the initial concentration.
S Fallah Jokandan, M Yegane Badi, A Esrafili, A Azari, E Ahmadi, H Tarhandeh, M Kermani,
Volume 12, Issue 2 (9-2019)
Abstract
Background and Objective: The activities of various industries produce a wide range of pollutants and toxic compounds. One of these compounds is the catechol, a cyclic organic compound with high toxicity and resistant to degradation. Therefore, the purpose of this study was to investigate efficiency of powder activated carbon magnetized with Fe3O4 nanoparticles in the removal of catechol from aqueous solutions by response surface methodology.
Materials and Methods: The co-precipitation method was used to synthesize magnetic powder activated carbon and its properties were analyzed by SEM and XRD analysis. Then, the effect of the parameters such as pH, contact time, absorbent dose, initial concentration of catechol and temperature on the efficiency of adsorption process were investigated using a response surface methodology (Box–Behnken). The residual concentration of catechol was measured by HPLC at 275 nm.
Results: The results showed that the maximum efficiency of the adsorption process was obtained at concentration of 20 mg/L, pH=3, contact time 90 minutes, at 25 °C and absorbent dose of 1.5 g/L. The study of isotherm and kinetics showed that the experimental data of the catechol adsorption process correlated with the Langmuir and pseudo-second order models, respectively. Thermodynamic study of the reaction also expresses the Exothermic and Spontaneous process.
Conclusion: The results showed that the adsorption process using powder activated carbon magnetized with Fe3O4 nanoparticles at acidic pH had better efficiency. As a result, the studied process as an effective, rapid and inexpensive method for removal of catechol from aqueous solutions is proposed. Due to its short reaction time, it is economically affordable process.
R Salmasi, A Behbahaninia, Ar Ostadrahimi,
Volume 12, Issue 2 (9-2019)
Abstract
Background and Objective: Heavy metals fixation in-situ by using inorganic amendments is a method for immobilization of polluted soils. The goal of this research was to determine efficiency of five amendments for heavy metals fixation of waste-water-irrigated soils around Tabriz city.
Materials and Methods: Cadmium, Pb, Cu, Ni, and Zn- containing solutions were added to 0.5 gram of five amendments including calcite, hematite, zeolite, illite, and bentonite. 10 soil samples from around of Tabriz city were taken. After shaking the samples, the concentrations of the five elements were determined in the filtered solution by using atomic absorption instrument. Retention capacity percentages of these elements were calculated, and the best amendments were determined by using Dunkan method.
Results: There were differences of heavy metals retention between amendments. Calcite had the highest retention of Cd (91%), Ni (78%), and Zn (94.7%); hematite had the highest Cu (90.5%) and Pb (94.3%); and illite showed the lowest retention of the 5 elements. Calcite, zeolite, bentonite, and hematite had significant higher retention capacities of Cd, Ni, and Zn in compared to 10 the soil samples.
Conclusion: Among the studied amendments, retention capacities of calcite and hematite for the five elements were higher than the remaining ones for addition to the soil. These two amendments can cause low uptake and low accumulation of the elements in agricultural crops in polluted soils.
H Niknejad, M Farzadkia, A Esrafili, M Kermani,
Volume 12, Issue 4 (2-2020)
Abstract
Background and Objective: 2,4 dinitrophenol is observed in sewage produced from chemical and petrochemical industries. Contamination of drinking water with these pollutants causes toxicity, health problems and change in taste and odor. The present study was developed to evaluate the efficiency of removal 2,4-DNP through dried sludge adsorbent and modified calcium chloride sludge adsorbent.
Materials and Methods: At first, sludge was dried at temperature of 60 °C. Next, CaCl2 was used to improve adsorption capacity. The removal efficiency of 2,4 dinitrophenol were determined by HPLC at wavelength of 360 nm. The effects of influencing factors including pH, initial pollutant concentration, contact time, and adsorbent dose were examined.
Results: The optimum pH of adsorption for both adsorbents was found to be 7. The optimum concentration of 2,4-DNP was 10 ppm. The results obtained from the present research showed that the removal of the contaminant using dried and modified sludge sorbent was increased from 72.6% to 86% at a dosage of 1.5 g. The adsorption kinetics were fitted with the pseudo second order kinetics model for both adsorbents. The isotherm data also showed that the adsorption of this pollutant on both adsorbents is fitted with the Freundlich model.
Conclusion: Results obtained from the present study indicated that the efficiency of the modified sludge ash is more than the non-modified sludge in 2,4 dinitrophenol removal. This can reduce adsorbent consumption in industrial treatment plants.
Azadeh Modiri, Shadab Shahsavari, Ali Vaziri Yazdi, Ali Akbar Seifkordi,
Volume 13, Issue 1 (4-2020)
Abstract
Background and Objective: Arsenic has long been considered as a heavy metal and toxic pollutant due to its potential to harm the human health and the environment. Adsorption is one of the mechanisms for arsenic removal from wastewater. Therefore, the purpose of this research was to investigate the feasibility of synthesized chitosan-zirconium magnetic nano fiber on arsenic adsorption from wastewater and to evaluate its kinetic and isotherm models.
Materials and Methods: Synthesis of nanofibers was performed by electrospinning method and the optimal formulation was determined following the experimental design. Then, kinetics and isotherms of arsenic adsorption on the as synthesized nanofibers were investigated. The prepared nanofiber was characterized using X-ray diffraction (XRD), Field Emission Scanning Electron Microscopes (FESEM), Infrared Fourier Transform (FT-IR) and Vibrational Sampler Magnetic Meter (VSM).
Results: The optimal formulation was obtained: 2.84% chitosan, 0.97% nano-zirconium and 0.94% nano-iron. The adsorption of arsenic on synthetic fibers was found to follow quasi-first-order kinetics and the Freundlich isotherm. Furthermore, the effect of initial concentrations of arsenic, contact time, temperature and pH on arsenic adsorption were surveyed. The optimal condition for nitrate arsenic adsorption was obtained at initial concentration of 70 mg/L, 45 min contact time and at pH 3.
Conclusion: According to the results, the synthesized nanofiber displayed a regular network structure with the distribution of the Zr-nanoparticles in its shape. Also, according to the form of magnetometric analysis, it was found that chitosan-nanosirconium magnetic nanofibers are well magnetized and are free magnetic. Finally, it can be concluded that the synthesized nanosorbent has a high potential for arsenic removal from industrial effluents.
Mansoureh Hamidi, Parvin Nassiri, Homayoon Ahmad Panahi, Lobat Taghavi, Saeed Bazgir,
Volume 13, Issue 3 (11-2020)
Abstract
Background and Objective: Noise pollution is one of the serious environmental issue. Sound control technologies based on sound absorption and sound insulation are considered as the two widely used methods. Therefore, the aim of this study was to modify silica aerogel nanocomposites to improve its acoustic properties.
Materials and Methods: This applied experimental research involved in examining eight various types of nanocomposites to evaluate their performance of acoustic properties. In this study, nanocomposites were synthesized by sol-gel method. For this purpose, TEOS and ethanol were added to SiO2 which subsequently stirred and diluted with ethanol as a precursor of silica sol. A solution of 5.5 M ammonium hydroxide is added drop-wise to the silica sol and then was stirred. The activated silica sol was quickly poured into the mold in which the samples were placed and finally placed in an oven at 150 °C for 3 hours. The acoustic properties of the samples were measured by the impedance tube and the reduction sound pressure level using a sound level meter. Each sample morphology was characterized by scanning electron microscopy.
Results: The sound absorption properties of as prepared nanocomposite relatively increased at high frequencies. The results indicated > 0.6 sound absorption coefficient by the modified nanocopmosites at higher frequencies. The sound absorption coefficient and transmission loss of D1 nanocomposite were higher at medium and low frequencies as compared to other nanocomposites. 4.6 and 9.73 dB average reduction of sound pressure level were achieved by either with or without nanocomposite enclosure, respectively, at a distance of 1 meter.
Conclusion: The results of the current study showed that the simultaneous addition of organic and mineral materials to silica aerogels (especially with the highest amounts of nanoclay) improves its acoustic properties, especially at medium and low frequencies. Among the samples, D1 nanocomposite shows better acoustic properties at medium and low frequencies. The sound absorption coefficient of D1 nanocomposite at frequencies of 315, 400, 500, 1000, 1250, 2000 Hz were obtained as 0.27, 0.38, 0.51, 0.78, 0.83 and 0.84, respectively. The findings also indicated 9.37 dB reduction of sound pressure level using D1 nanocomposite.
Nahied Shahbodaghi, Daryoush Afzali, Maryam Fayazi,
Volume 15, Issue 1 (4-2022)
Abstract
Background and Objective: With increasing water pollution, serious water shortages and increased pressure to save water, recycling and reuse of water has attracted more attention in various industries. Removal of silica from cooling water is essential for recycling and reuse of water. The aim of this study was to remove silica from water using magnesium oxide nanoparticles (MgO) synthesized by chemical deposition method.
Materials and Methods: Synthetic nanoparticles were successfully determined using field emission scanning electron microscopy (FE-SEM), Fourier transform infrared (FTIR) and X-ray diffraction (XRD). To determine the optimal adsorption conditions the batch system, the effect of important parameters such as pH (2-8), contact time (0-150 min), initial concentration of silica solution (50-1000 mg/L), adsorbent amount (0.01-0.14 g) and temperature (25-60 ˚C) were studied.
Results: Under optimal conditions, an almost removal of 200 mg/L silica solution was achieved in 60 min reaction time. Equilibrium data were analyzed using the Langmuir and Freundlich isotherms. The adsorption process can be well described by the Langmuir model, and the maximum adsorption capacity was calculated as 75.76 mg/g. Synthetic data were analyzed using pseudo-first-order and pseudo-second-order equations. The pseudo-second-order model showed good agreement with the obtained data (R2 = 0.9949).
Conclusion: Due to the high potential of magnesium oxide nanoparticles in silica removal, it can be a good candidate for the removal of silica and industrial wastewater treatment.
Mohammad Ghafoori, Mehrdad Cheraghi, Maryam Kiani Sadr, Bahareh Lorestani, Soheil Sobhanardakani,
Volume 16, Issue 2 (9-2023)
Abstract
Background and Objective: Antibiotics are emerging pollutants that enter the human environment through pharmaceutical, hospital, and urban wastewater. Therefore, this study was conducted to investigate of removal efficacy of tetracycline (TC) from aqueous solutions using GO@Fe3O4@β-CD.
Materials and Methods: In this descriptive study, GO@Fe3O4@β-CD was synthesized and then used as an adsorbent for the removal of TC from aqueous solution. GO@Fe3O4@β-CD was characterized using X-ray diffraction (XRD), Scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometry (VSM) methods. Also, the influence of variables including pH (3-9), amount of adsorbent (0.003-0.050 g), contact time (0-100 min), and temperature (25-55 °C) so assessed on the efficacy of TC removal.
Results: The results of TGA analysis showed that GO@Fe3O4@β-CD nanoparticles were resistant to temperatures up to 400 °C. Also, the results indicated that β-cyclodextrin was uniformly dispersed on the surface of GO@Fe3O4.
The results indicated that removal efficiency increased up to 60 min contact time, 0.01 g of adsorbent, and decrease temperature to 25 °C. The optimum pH for TC removal was 7.0. Also, under these conditions, the adsorption process followed the Langmuir adsorption isotherm with a correlation coefficient of 0.992 and the pseudo-second-order kinetic model with a correlation coefficient of 0.997, 0.999, and 0.998. The maximum adsorption capacity of the prepared adsorbent was 357 mg/g.
Conclusion: The GO@Fe3O4@β-CD could be an effective and efficient adsorbent for the removal of TC from industrial wastewater.
Mohammad Hossein Fekri, Samaneh Soleymani, Maryam Razavi Mehr, Fatemeh Saki,
Volume 16, Issue 2 (9-2023)
Abstract
Background and Objective: Due to the presence of industrial pollutants in water sources, it is necessary to treat wastewater, especially colored wastewater. This study aims to treat wastewater containing methyl orange dye using nano mesopore SBA-16.
Materials and Methods: In this study, the effect of different parameters (pH, concentration of methyl orange, amount of adsorbent, temperature, and contact time) on the absorption of methyl orange by nanocomposite prepared with the help of Design of Experiment 7 software and Response Surface Method (RSM) was investigated.
Results: The maximum amount of pollutant removal by the adsorbent was obtained under optimal conditions of pH = 4.07, temperature 50 °C, contact time 35 minutes, initial concentration of adsorbent 10 mg/L, and amount of adsorbent 0.04 g. Also, the findings showed that the absorption behavior is most consistent with the Langmuir isotherm and the absorption process is exothermic and spontaneous at low temperatures.
Conclusion: In optimal conditions, the SBA-16 adsorbent was able to remove 98.60 % of methyl orange from the aqueous solution and the maximum adsorption capacity (qmax) for the removal of methyl orange pollutant was 37.73 mg/g. Considering the high potential of nano mesopore SBA-16 in removing methyl orange pigment, it can be considered a suitable candidate for removing colored pollutants and treating wastewater from textile factories.
Mahboub Saffari,
Volume 16, Issue 3 (12-2023)
Abstract
Background and Objective: Nowadays, the use of biochar as a new and suitable adsorbent to remove inorganic pollutants from water sources has grown significantly. The present study was conducted to evaluate the effects of biochar physical modifications compared to unmodified biochar on nickel (Ni) removal efficiency in aqueous solutions.
Materials and Methods: After the production of cypress cones biochar (RB), biochar particles (<164 µm) were crushed into very small (<26 µm) dimensions (BMB) using a planetary ball mill and after evaluation their various properties by SLS, BET, FTIR and SEM techniques, their application (RB and BMB) in optimizing the Ni removal from aqueous solutions were evaluated using the response surface methodology (RSM: Box-Behnken design).
Results: Based on the results, the physical modification of biochar (BMB) decreased the particle size by 6.2 times, increased the specific surface area by 4.9 times, increased (containing oxygen) and decreased (aliphatic and OH stretching groups) of specific functional groups and finer surface morphology, compared to RB. The use of BMB in the aqueous solution caused an increase of 9.7% (on average) in the removal of Ni compared to the RB sample. The fitting of the data obtained from Ni removal in the Box-Benken model in both adsorbents shows the appropriate prediction of this model in the optimization of Ni removal from aqueous solutions.
Conclusion: According to the results of this research, the physical modification of biochar, as a simple, cheap, and environmentally friendly method, due to the increase in the efficiency of Ni pollutant removal, can be introduced as a suitable method in the activation of biochar, which further research is required based on the type of biochar and various pollutants.
Yadollah Yousefzadeh, Vida Izadkhah, Soheil Sobhanardakani, Bahareh Lorestani, Sedigheh Alavinia,
Volume 16, Issue 4 (3-2024)
Abstract
Background and Objective: Antibiotics as emerging pollutants are harmful to environmental health. Therefore, this study was conducted to investigate the efficiency of Uio-66-NH2@CS-Iso-Gu nanohybrid for the removal of amoxicillin (AMX) from aqueous solutions.
Materials and Methods: In this study, for the first time, guanidine and isocyanate monomers are cross-linked with chitosan. The combination of this polymer with organometallic compounds contributes to its chemical/thermal stability and reusability. Uio-66-NH2@CS-Iso-Gu nanohybrid was characterized using X-ray diffraction (XRD), Scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA), and BET methods. Also, the effects of pH, initial concentration of AMX, contact time, and temperature were evaluated. Moreover, isotherm, kinetic and thermodynamics studies were performed.
Results: The results of TGA analysis showed that Uio-66-NH2@CS-Iso-Gu nanohybrid was resistant to temperatures up to 400 °C. Also, optimal adsorption of AMX occurred in the first 25 min. The synthesized nanohybrid has a surface area of 101.2 m2/g and a type IV isotherm. Acidic groups were present on the synthesized nanohybrid surface based on the pHpzc = 4.7. Langmuir (for 25 °C and 45 °C) and Freundlich (for 65 °C) isotherm models and pseudo-second-order kinetic models are more appropriate to fit the adsorption data with the experimental data. The maximum adsorption capacity of the synthesized nanohybrid was equal to 56.49, 40.65, and 0.382 mg/g at temperatures of 25°C, 45°C, and 65°C, respectively. Based on the findings, Uio-66-NH2@CS-Iso-Gu nanohybrid could be used for up to five cycles without significantly reducing their performance.
Conclusion: The results showed that Uio-66-NH2@CS-Iso-Gu nanohybrid has a significant efficiency for removing AMX and could be used as an effective adsorbent for the treatment of wastewater containing pharmaceutical residues.
Omid Mohammadi Moinalzoafa, Maryam Tahmasebpoor,
Volume 17, Issue 4 (3-2025)
Abstract
Background and Objective: The global increase in energy consumption has led to a rise in carbon dioxide emissions, causing significant and often irreparable damages such as global warming. This study investigates the adsorption capacity of hairy nanocrystalline cellulose as a novel adsorbent and seeks to enhance its performance in carbon dioxide capture by modifying it with two types of amines: monoethanolamine and diethanolamine.
Materials and Methods: Hairy nanocrystalline cellulose was synthesized through oxidation and amine modification. The formation of chemical groups and sample morphology was analyzed using Fourier transform infrared spectroscopy and field emission scanning electron microscopy. Additionally, thermogravimetric analysis was performed at two temperatures (25 and 50 °C) and two concentrations (10% and 90% carbon dioxide in nitrogen) to evaluate the adsorption capacity of the samples.
Results: The results showed that at 25 °C and a carbon dioxide concentration of 90%, the adsorption capacities of hairy nanocrystalline cellulose, cellulose modified with 20% by weight of monoethanolamine, and cellulose modified with 20% by weight of diethanolamine were 1.74, 2.5, and 1.96 mmol/g, respectively. These findings indicate that modifying the adsorbent with monoethanolamine increased its carbon dioxide adsorption capacity by approximately 44%, while modification with diethanolamine resulted in a 13% improvement.
Conclusion: The findings suggest that hairy nanocrystalline cellulose, particularly in its modified forms, holds significant promise as a novel and effective adsorbent for carbon dioxide capture.
Hanieh Mirbolooki, Shahriar Mahdavi, Eisa Solgi, Babak Razdar, Mahboubeh Zarabi, Davoud Akhzari,
Volume 17, Issue 4 (3-2025)
Abstract
Background and Objective: Dyes are among the most widespread pollutants found in industrial wastewater. The aim of this study is to investigate the potential of vineyard wood waste as a green adsorbent for the removal of polyazo solophenyl dye from aquatic environments.
Materials and Methods: In this laboratory research, two forms of adsorbents modified with H₂SO₄ and NaOH were used. Data obtained from dye adsorption in synthetic solutions were fitted to isotherm, kinetic, and thermodynamic models, with all calculations performed using Excel software. Zeta potential analysis, along with FTIR, BET, and FESEM-EDS instrumental analyses, was conducted to determine the properties of the adsorbent. Additionally, the desorption rates of the adsorbents were analyzed.
Results: The results showed that the highest color removal efficiency for the adsorbent modified with H2SO4 was achieved at a contact time of 180 minutes and a reaction temperature of 50 °C, while for the adsorbent modified with NaOH, the highest efficiency was observed at a contact time of 105 minutes and a reaction temperature of 25 °C. For both adsorbents, the optimal pH was 4, and the optimal adsorbent dosage was 1 g. The adsorption data for both modified adsorbents followed the pseudo-second-order kinetic model, while the equilibrium data aligned with the Freundlich and Temkin isotherm models. The adsorption capacities were found to be 22.27 mg/g and 9.87 mg/g for the adsorbents modified with acid and base, respectively, under optimal conditions.
Conclusion: This study introduces a novel, low-cost adsorbent derived from natural waste for water pollution removal, transforming the current approach into a cost-effective and eco-friendly solution.
