Showing 21 results for Nasseri
M.h Dehghani, S Nasseri, M Ghaderpoori, A.h Mahvi, R Nabizadeh Nodehi,
Volume 3, Issue 4 (8 2011)
Abstract
Backgrounds and Objective: Surfactants are one of the largest pollutants which exist in urban and industrial wastewaters. Large quantities of surfactants have entered to the environment since last decade due to increased use of synthetic detergent in industrial and home consumptions.In this study, the efficiency of UV/H2O2 process in removal of linear alkylbenzane sulfonate (LAS) from aqueous solutions was investigated.
Materials and Methods: In this study methylene blue active substane(MBAS)method and spectrometery were used to determine anion and residual surfactant respectively. In this study important variables were H2O2 concentration, initial concentration of surfactant, pH and duration of UV radiation. The effect of UV/H2O2 process on the degradation of LAS was analyzed statistically by using Multiple Linear Regression test.
Results: The resulted showed that after 20 minute, ultraviolet radiation solely removed 38.44 percent of Anionic detergent, Hydrogen peroxide showed no significant removal of detergent solution in the time course study. The efficiency of UV/H2O2 process in 10, 20 and 30 minute were to 86.2, 90 and 96.5 %, respectively.
Conclusion: The results showed that the efficiency of ultraviolet radiation and hydrogen peroxide process in anionic detergent was not significant thoogh it was considerable in combination process (UV/H2O2).
S Hemmati Borji, S Nasseri, R Nabizadeh Nodehi, A.h Mahvi, A.h Javadi,
Volume 3, Issue 4 (8 2011)
Abstract
Backgrounds and Objectives: Phenol and phenolic compounds are widely used in industry and daily liFe, and are of high interest due to stability in the environment, dissolution ability in water and health problems. In this regard, phenol removal from water is of high importance. The purpose of this study was to investigate the efficiency of photodegradation process for removal of phenol from aqueous system by use of Fe-doped TiO2 nanoparticles prepared by sol-gel method.
Materials and Methods: Phenol concentrations of 5, 10, 50 and 100 mg/L were prepared and exposed to UV and Fe-doped TiO2, separately and simultaneously. Also the effect of initial phenol concentration, Fe-doped TiO2 loading and pH were studied. Various doses of photocatalist investigated for Fe- doped TiO2 were 0.25, 0.5 and 1 g/L. pH was studied at three ranges, acidic (pH=3), neutral (pH=7) and alkaline (pH=11).
Results: Maximum degradation was obtained at acidic pH, 0.5 g/L of Fe-doped TiO2 for all of phenol concentrations. With increasing initial concentration of phenol, photocatalytic degradation decreased. In comparison with Fe-doped TiO2/UV process, efficiency of UV radiation alone was low in phenol degradation (% 64.5 at 100 mg/l of phenol concentration). Also the amount of phenol adsorbed on the Fe-doped TiO2 was negligible at dark conditions.
Conclusion: Results of this study showed that Fe(III)- doped TiO2 nanoparticles had an important effect on photocatalytic degradation of high initial phenol concentration when Fe(III)-doped TiO2/ UV process applied.
Kazem Naddafi, Mehran Mohammadian Fazli, Ali Reza Mesdaghinia, Simin Nasseri, Mahnaz Mazaheri Assadi, Masoud Yunesian,
Volume 5, Issue 2 (13 2012)
Abstract
MicrosoftInternetExplorer4
Background and Objectives: Environmental pollution and health risks of dyestuffs
extensively are caused by many industries. Nonbiodegradability of dyes is
important so that different methods are studied for removing them. The use of
white rot fungi is promising technique in this regard. Therefore, objective of
this work is to investigate Rimazol Brilliant Blue Royal decolorization by
immobilized Ganoderma sp. in sodium alginate from aqueous solution.
Material and Methods: This is an experimental study. First, the nutritional, environmental, and
operational conditions of decolorization process were optimized. Then,
efficiency of immobilized fungal cells was investigated. Experimental designs
were provided using fractional factorial methods and quadratic model was fitted
on decolorization data by MiniTab software.
Results: Our findings
showed that type and concentration of carbon source, temperature, and pH were
the most important factors affecting decolorization and statistically
significant. Optimal conditions to 95.3 percent color removal were: glycerol as
carbon source at 19.14 g/L temperature, 27 oC and initial pH, 6.26. Moreover,
decolorization efficiency increased from 75 percent up to 95 percent by improving
process and fungal immobilization.
Conclusion: Ganoderma
fungus has suitable potential to decolorization. Besides, optimization and cell
immobilization can improve its capability. Application of experimental design
to research methodology is important because of decreasing in experiments and
saving resources. It is suggested to use these potentials in environmental
pollution control.
Saeed Parastar, Simin Nasseri, Amir Hossein Mahvi, Mitra Gholami, Amir Hossein Javadi, Saeedeh Hemmati,
Volume 5, Issue 3 (21 2012)
Abstract
Background and Objectives: Pollution of water resources to nitrate is an
environmental problem in many parts of the world. This problem possibly causes
diseases such as methemoglobinemia, lymphatic system cancer and Leukemia.
Hence, nitrate control and removal from water resources is necessary.
Considering that application of nanomaterials in treatment of environmental pollutants
has become an interesting method, in this research use of Ag-doped TiO2 nanoparticles synthesized through photodeposition produced under UV irradiation
was studied for removal of nitrate from aqueous solutions.
Materials and Methods: Three nitrate concentrations of 20, 50, and 100 mg/L were considered. In order
to determine the effect of Ag-doped TiO2 nanoparticles on nitrate removal, dosages of 0.1, 0.4, 0.8 and 1.2 g/L nanoparticles were
used pH range of 5-9 was also considered. The effect of Ag-doped TiO2 nanoparticles both in darkness and under UV irradiation was studied. Moreover,
the presence of chloride and sulfate anions on the system removal efficiency
was investigated.
Results: The optimum
performance of nitrate removal (95.5%) was obtained using nitrate concentration
of 100 mg/L, in acidic pH and 0.8 g/L Ag-TiO2. Increase of
nanoparticle dosage up to 0.8 g/L, increased the removal efficiency, but for
1.2 g/L dosage of nanoparticles, the removal efficiency decreased. Maximum
reduction performance without nanoparticles, under UV irradiation and under
darkness conditions were 32% and 23.3% , respectively. In addition, we found
that presence of sulfate and chloride anions in aqueous solution reduced
efficiency of nitrate removal.
Conclusion: Results of
this study showed that Ag-doped TiO2 nanoparticles may be
efficiently used for nitrate removal from aqueous solutions.
Hafez Golstanifar, Simin Nasseri, Amir Hossin Mahvi, Mohamad Hadi Dehghani, Anvar Asadi ,
Volume 5, Issue 4 (15 2013)
Abstract
Background and Objectives: The contamination of nitrate (NO3−) in groundwater resources causes two adverse health effects: induction of “blue-baby syndrome” (methemoglobinemia), especially in infants, and the potential formation of carcinogenic nitrosamines. The aim of this research is to investigate nitrate removal from groundwater using alumina nanoparticles and to determine the adsorption isotherms.
Materials and Methods: This analytical-descriptive study was carried out at lab-scale, under batch conditions, and at room-temperature. The structure of alumina nanoparticles was determined using XRD, SEM, and TEM techniques. The concentration of nitrate in the solutions was determined by spectrophotometer at wavelengths of 220 and 275 nm. In addition, we investigated the impact of the important operational parameters including initial dose of Al2O3 (0.06-0.25 g/l), initial concentration of the solution (50- 300 mg/l), contact time (5-60 min), and pH (3-9). Moreover, we used Freundlich and Langmuir isotherm models to calculate equilibrium constant.
Results: It was found that nitrate removal efficiency increased as we increased contact time, initial concentration and pH in batch system. A maximum of 60% nitrate removal was achieved under following conditions: 60 min contact time, pH 5, and initial nitrate concentration of 300 mg/l as N. The obtained results showed that the adsorption of nitrate by Nano-Gamma-Alumina follows Langmuir isotherm equation with a correlation coefficient equal to 0.982.
Conclusion: Overall, our findings showed that the alumina nanoparticles can be used as an effective adsorbent to remove NO3 from aqueous solutions.
Amir Hossein Mahvi, Noushin Rastkari, Ramin Nabizadeh Nodehi, Shahrokh Nazmara, Simin Nasseri, Mahboobeh Ghoochani,
Volume 6, Issue 3 (12-2013)
Abstract
Background and Objectives:Chlorination is the most common method of water disinfection. Chlorine reaction with natural organic compounds nor removed completely during treatment process would result in forming disinfection byproducts. Followed by trihalomethanes, Haloaceticacides are the second main byproducts of chlorination in water. The research works conducted in Iran have assessed trihalomethanes. Hence, this is the first time we are reporting haloacetic acids in Iran.
Materials and Methodology: We collected samples from surface water resources and treated water in Tehran for six consecutive months (first half, 2010). We measured temperature, pH, UV adsorption at 254 nm and TOC in each surface water sample and analyzed pH, residual chlorine, and haloacetic acids in the treated water samples.
Results: We found that TOC in surface water resources is 3.6-4.42 and 1.78-2.71 mg/l in spring and summer respectively. Moreover, haloacetic acids concentration was found to be 41.7-55.56 and 34.83-43.73 μg/l in spring and summer respectively.
Conclusion: Our results revealed that concentration of NOM, TOC, and HAAs was more in spring than summer. In addition, concentration of HAAs was depended up on NOM and TOC. Considering maximum permeable concentration of HAAs (60 μg/l) by EPA, it can be claimed that concentration of HAAs was less than the maximum permissible level in all of the samples. However, the immanency of the monitored values to the standard values can be a warning for concerned authorities in water industry.
Masoumeh Golshan, Simin Nasseri, Mahdi Farzadkia, Ali Esrafili, Roshanak Rezaei Kalantary, Leila Karimi Takanlu,
Volume 7, Issue 2 (10-2014)
Abstract
Background and Objectives: The use of surfactants enhance the bioavailability of nonbiodegradable contaminants such as PAHs. Biosurfactants are more environmental friendly. In this study the ability of removing phenenthrene from soil by biosurfactant was assessed and compared with that of chemical surfactant. Materials and Methods: A soil sample free of any organic or microbial contamination was artificially spiked with phenanthrene at two concentrations. Then, mineral salt medium at constant concentration of chemical surfactant TritonX-100 and rhamnolipid MR01biosurfactant was added to it in order to have the proportion of 10% w:v (soil:water). A microbial consortium with a potential of phenanthrene biodegradation was inoculated to the soil slurry in two densities (OD=1 and 2) and then it was aerated on a shaker. After eight weeks, the residual concentration of phenanthrene in the soil was extracted by ultrasonic and was analyzed using HPLC. MPN test was used for measuring microbial population. This study was conducted based on the two level full factorial design of experiment. Results: It was found that chemical surfactant exhibited higher PHE removal efficiency than the biosurfactant. Using 120 mg/L of TritonX-100 and rhamnolipid, the PHE removal for the soil contaminated with 50 mg PHE/kg dry soil was 98.5 and 88.7% respectively, while the removal efficieny was decreased to 87 and 76% respectively for the soil contaminated with 300 mg PHE/kg. In the absence of surfactant, the removal efficiency at concentrations of 50 and 300 mg PHE/kg dry soil was achieved 60.76 and 51% respectively. The phenanthrene removal efficiency in OD=2 was more higher than OD=1. In the presence of rhamnolipid, the maximum microbial populations was observed in the second week, while it decreased in the presence of TritonX-100. Conclusion: Use of biosurfactants can be considered as a suitable option in low level pollutant sites. Chemical surfactants as ex-situ has achieved more satisfactory results in high level contaminant sites.
E. Karimi Pasandideh, R. Rezaei Kalantary, S. Nasseri, A. H. Mahvi, R. Nabizadeh, A. Esrafili,
Volume 7, Issue 3 (5-2014)
Abstract
Background and Objective: The presence of natural organic materials (NOM) in water resources affects its quality (i.e. color, odor, and taste). In addition, it leads to the fouling of filters and membranes and reduces water treatment efficiency during flocculation/ coagulation. Moreover, NOM reacts with disinfectants and produces byproducts (DBPs), which are harmful to human health. Magnetic nanoparticles have been reported as effective adsorbents for the removal of pollutants from the aqueous media. In this study, we applied SiO2coating on these nanoparticles in order to enhance their stability and dispersion in aqueous media and investigated their capability in NOM adsorption from water. Materials and Methods: Iron oxide magnetic nanoparticles were prepared by co-precipitation. Then, we added Tetraethoxysilane (TEOS) to the solution in order to coat it with SiO2 . The adsorbent characteristics were determined by SEM and XRD. Then, we carried out the adsorption experiments under different pH(3-12) and contact time (5-240 min)performance conditions. The adsorption kinetic was determined with respect to different Humic acid adsorption times. Later, we determined the effect of different concentrations of adsorbent on different concentrations of Humic acid, and Langmuir and Freundlich coefficients based on the optimum conditions. Results: The morphology investigation of adsorbent showed the average size of Fe3O4/SiO2nanoparticles was 30-130 nm. The pH value of 10.5 and the contact time of 90 min at room temperature were determined as optimum conditions for removal of humic acid using Fe3O4/SiO2 nanoparticles. The maximum adsorption capacity of Fe3O4/SiO2 was192.30. The adsorption isotherm was fitted well by Langmuir model (R2>0.90) and the pseudo-second order model (R2>0.98) could better explain humic acid adsorption. Conclusion: Having high number of active surface sites, magnetic properties, easily separation using magnetic field, and its cost-effectiveness, the Fe3O4/SiO2 nanoparticles could be used as an efficient adsorbent in removal of humic acid from water.
A Naghizadeh, S Nasseri,
Volume 8, Issue 2 (8-2015)
Abstract
Background and Objective: Natural organic matters (NOMs) are a mixture of chemically complex polyelectrolytes with varying molecular weights, produced mainly from the decomposition of plants and animal residues. Various purification methods are used for removal of NOMs from water. The objective of this study was to remove NOMs from aqueous solution using reformed continuous carbon nanotubes column. Materials and Methods: The removal of NOMs from aqueous solution using reformed continuous carbon nanotubes column was studied. Effect of several variables such as zero point of pH (pHZPC), pH, influent concentration of natural organic matters were studied and different isotherms were assessed. Results: Investigation of pH effect showed that the adsorbability of NOMs increased with decreasing of pH. The experiments indicated that carbon nanotubes (CNT) samples exhibit pHZPC around 6. Results from Freundlich, Langmuir, and BET isotherm experiments revealed that the correlation coefficient R2 in Freundlich model was higher than that of Langmuir. In addition, experiments of continuous flow in different initial concentrations of NOMs showed that the adsorption capacities of CNT were 53.46, 30.40, and 24.75 mg/g for NOMs initial concentrations of 10, 5, and 3 mg/L, respectively. Conclusion: The present study shows that CNTs have high potential for adsorption of NOMs from aqueous solution
H Zarei, A.h Mahvi, S Nasseri, R Nabizadeh Noudehi, F Shemirani,
Volume 8, Issue 3 (12-2015)
Abstract
Objective and Background: Fluoride is an element widely found in the earth crust. Advantages and disadvantages of fluoride in the human body are depended on its concentration. Long-term consumption of drinking water contaminated with arsenic can cause adverse health effects such as skin lesions and cancer in humans. The aim of this study was to study efficiency of nano alumina on multi walled carbon nano tube for removal As(V) and fluoride from aqueous solution.
Materials and Method: In this study, nano-scale crystalline alumina was synthesized on single walled carbon nanotube by sol-gel method for using as a sorbent for solid phase extraction of Fluorine ion and arsenic(V). Response surface methodology based on Box-Behnken was used to assess the effect of independent variables on the response function and prediction of the best response value. In this study, effect of different parameters, such as contact time (10 to 120 min), pH (3-9), adsorbent dosage (0.25-1.5 g/L) and initial concentration of fluoride (2-8 mg/L) on efficiency of process was investigated. The structure of nano-scale alumina on multi walled carbon nano tube was determined by XRD and SEM techniques. Moreover, Freundlich and Langmuir isotherm models were used to calculate equilibrium constant.
Results: It was found that by increasing contact time and adsorbent dosage the rate of fluoride removal increased. However, by increasing pH and initial concentration the efficiency of fluoride removal decreased. High value for R2 (0.94) shows that removal of arsenic(V) can be described by this model. The Freundlich isotherm was the best fitted graph for experimental data with R2 more than 0.997.
Conclusion: In this study, it was observed that efficiency of arsenic(V) and fluoride removal was greatly increased by using nano-scale alumina on multi walled carbon nanotubes (MWCNTs).
K Naddafi, R Nabizadeh, S Nasseri, K Yaghmaeian, A Koolivand,
Volume 8, Issue 3 (12-2015)
Abstract
Background and Objectives: Remaining of crude oil in storage tanks usually results in accumulating oily sludge at the bottom of the tank, which should be treated and disposed of in a suitable manner. The efficiency of in-vessel composting process in removing total petroleum hydrocarbons (TPH) from bottom sludge of crude oil storage tanks was investigated in the present study.
Material and methods: The sludge was mixed with immature compost at the ratios of 1:0 (as control), 1:2, 1:4, 1:6, 1:8, and 1:10 (as dry basis) with the initial C:N:P and moisture content of 100:5:1 and 55% respectively for a period of 10 weeks. The moisture adjustment and mixing process were done 3 times a day during the composting period. Sampling and analysis of TPH and pH were done every week and every two days, respectively.
Results: TPH removal in the 1:2, 1:4, 1:6, 1:8, and 1:10 composting reactors was 66.59, 73.19, 74.81, 80.20, and 79.91%, respectively. Thus, initial adjustment of sludge to immature compost ratios plays a great role in reduction of TPH. The results of the control reactors indicated that the main mechanism of TPH removal in the composting reactors was biological process.
Conclusions: In-vessel composting by addition of immature compost as amendment is a viable choice for bioremediation of the bottom sludge of crude oil storage tanks.
Y Dadban Shahamat, M Farzadkia, S Nasseri, A.h Mahvi, M Gholami, A Esrafily,
Volume 8, Issue 3 (12-2015)
Abstract
Background and Objectives: Phenol is one of the industrial pollutants in wastewaters, which due to its toxicity for biological systems various pretreatment processes have been used for its detoxification. In this study, the combination of catalytic ozonation process (COP) and sequencing batch reactor (SBR) were used for detoxification of these types of wastewaters.
Materials and Methodology: In this study, the effect of COP on phenol degradation, COD removal, and detoxification of wastewater was investigated. To determine the acute toxicity of effluents and identification of intermediate compounds produced in COP, bioassay using Daphnia Magna and GC / MS were used, respectively. Then, phenol and COD removal of pretreated wastewater was investigated in SBR.
Results: It was found that under optimal conditions in COP (time = 60 min), the concentrations of phenol and COD reduced from 500 and 1162 to 7.5 and 351 mg/L respectively and pretreated effluent toxicity (TU = 36), after rising in the initial stage of reaction, effectively reduced at the end of process (TU=2.3). the integration of this process with SBR could decreased the COD and phenol concentration less than the detectable range by HPLC.
Conclusion: Results showed that COP has a high effect on biodegradability, detoxification, and mineralization of phenol and combination of COP with SBR process can effectively treat wastewaters containing phenol.
A Naderi, S Nasseri, A.h Mahvi, M.r Monazzam,
Volume 8, Issue 4 (3-2016)
Abstract
Background and Objectives: Due to the increasing use of mobile phone in recent years, the number of BTS antennas has also increased. .Proliferation of BTS antennas in cities and villages, and perpetuation of encountering with waves from one side and increasing the anxiety of many people in encountering with their waves from the other side convinced more investigations in this field. Therefore, the purpose of this study was to investigate the propagation of microwave around the BTS antennas of Maragheh and to compare power density measurements with allowable environmental standards.
Material and Methods: In this research, the frequency of BTS antennas was determined through field monitoring. Then, measurements were performed using a calibrated Spectran 4060 and the standard method IEEE Std C95.1 was adopted in close and far fields from each antenna. Then, the obtained data were analyzed after entering to SPSS environment. In this study, the Kolmogrov-Smirnov test, Kruskal-Wallis, and Mann-Whitney tests were used.
Results: This research found that in both Irancel and Hamrah Aval operators, the power density increased with distance in close fields and decreased in far fields. Moreover, at the distance of 20 meter, the maximum value of power density was measured. Significant difference between these distances was observed (P-value ≤0.05).
Conclusion: Out of 1804 cases in far and close fields, the highest power density measured at 900 MHz band was 4.51 mW/m2, which is in accordance with 0.1% permissible exposure.
F Khalili, A.h Mahvi, S Nasseri, M Yunesian, B Djahed, M Yaseri,
Volume 9, Issue 1 (6-2016)
Abstract
Background and Objectives: Chemical hair color are one of the most widely used cosmetics. The presence of heavy metals in these products can affect the health of consumers. Unlike other cosmetics, no study has been conducted on the heavy metal levels in the synthetic chemical hair colors. This study determined the concentration of heavy metals in these products and the risk assessment of non-carcinogenic effects by these elements were calculated.
Material and Method: 32 samples of chemical hair color from eight brands (3 local and 5 imported ones) and four most used colors were collected from the markets in Tehran. The concentration of cadmium, lead, and barium was determined using ICP-MS. The information required to assess exposure risk was gathered through a questionnaire distributed among citizens of Tehran. The assessment of exposure was conducted using Mont Carlo method and non-carcinogenic risk was determined using the index of Hazard Quotient. .
Results: Barium concentration measured was 0.86 mg/kg and concentrations of Cadmium and Lead were 0.45 and 185.34 µg/kg respectively. Among the elements, Pb with Hazard Quotient equals to 7.46×10-4 had the most risk and cadmium with Hazard Quotient equals to 3.57×10-5 had the lowest risk. Moreover, the Iranian brand and blond had the highest risk among the samples.
Conclusion: Based on the index of Hazard Quotient, heavy metals in the studied samples had no risk for consumers of these products.
Ar Mesdaghinia, S Nasseri, M Hadi,
Volume 9, Issue 3 (12-2016)
Abstract
Background and Objective: Exposure to chemicals such as heavy metals can be occurred through the route of drinking water consumption. Chromium is an important pollutant because of its role in the appearance of carcinogenic and non-carcinogenic health effects in humans. In this study, we studied the carcinogenic risk and non-carcinogenic hazard of chromium due to the consumption of bottled drinking water distributed throughout Iran.
Materials and Methods: The Hazard Quotient (HQ) and Excess Lifetime Cancer Risk (ELCR) indices were calculated. Monte-Carlo simulation technique was adopted for simulating uncertainty in the estimation of HQ and ELCR based on the input variables namely the concentration of pollutant, per capita water consumption, body weight, reference dose, biological availability, and source contribution factors.
Results: The average concentration of chromium in bottled waters determined was 4.79 ± 2.32 µg/L. The amounts of HQ and ELCR for the age groups of lower than 2, 2 to 6, 6 to 16 and over 16 years old were 0.000354, 0.00292, 0.00236, 0.00147 and 4.04×10-11, 5.99×10-10, 8.61×10-10 and 2.34×10-9, respectively.
Conclusion: In regard to the concentration of chromium in bottled waters in Iran, the incidence probability and the possibility of carcinogenic and non-carcinogenic effects by this pollutant due to the consumption of bottled water are considerably low and there is no health concern for any age groups.
R Nabizadeh Nodehi, Ar Mesdaghinia, S Nasseri, M Hadi, H Soleimani, P Bahmani,
Volume 9, Issue 4 (3-2017)
Abstract
Background and Objective: Water corrosion and scaling are known as destructive phenomenon of drinking water quality and water facilities. In this study, the groundwater tendency to corrosion or scaling in source water, water storage reservoirs and distribution system were studied. Simultaneous use of some qualitative and a quantitative index along with statistical analyses to assess the water scaling or corrosion tendency were investigated.
Materials and Methods: The data analysis of groundwater, water storage reservoirs and water distribution system in rural area of Kurdistan province were analyzed and the amount of Langelier (LI), Ryznar (RY), Pockorius (PSI) and Larson–Skold (LS) and CCPP indices were determined. Corrosion and scaling threshold for qualitative indices were determined based on CCPP index. The mean of indices was compared with the thresholds using independent t-test. ANOVA was used to assess the difference between the indices in different sources of water.
Results: The balance range for LI, RY and PSI found to be -0.1-0.05, 7-9 and 7.1-8.5. The mean CCPP for groundwater, reservoirs and networks were 9.27 ± 1.29, 9.13 ± 1.25, 11.25 ± 1.23, respectively. All three sources of water have some tendencies toward scaling; however, a significant balance status was confirmed statistically. According to Larson–Skold index, sulfate and chloride anions did not play a role in scaling process.
Conclusion: The use of qualitative indices with CCPP index can provide more accurate estimation of water tendency toward scaling or corrosion. The assessment of qualitative indices along with CCPP is recommended in drinking water corrosion monitoring studies.
Ar Mesdaghinia, S Nasseri, M Hadi, E Iravani, M Askari,
Volume 10, Issue 4 (3-2018)
Abstract
Background and Objective: Supply of safe drinking water to each community is one of the most important challenges in improving the general community’s health. Considering the importance of the research on water quality, identification of water quality research gaps was performed by reviewing the relevant studies through a systematic review for Iran.
Materials and Methods: In this study 638, 166, 300 and 1000 relevant articles were found on Scopus, SID, Magiran and Iranmedex databases, respectively. Out of 2104 articles, 1394 articles were excluded from the study. Finally, 710 articles were further reviewed.
Results: Monitoring of pollutants by a descriptive study was the main objective of the most studies (36.62%). Around 13% of the studies were performed on a laboratory scale. Organic pollutants in Iran have been concerned only in 17 provinces, and other provinces have not participated in this regard. Nitrate is studied in around one fifth of the total studies. Heavy metals were also considered as a parameter of concern in the studies carried out on monitoring drinking water resource quality.
Conclusion: This study reflects the research gaps and provides a basis for prioritizing water quality research in Iran. More actions and sound planning should be taken to monitor organic and inorganic pollutants. Chemical and microbial risk assessment, tracing the fate of pollutants and assessment of their ecological effects, investigations on advanced water purification processes, the use of bioremediation methods, identification of biological contaminant using biomarkers and molecular identification techniques are the most important research priorities that require more investigations.
R Mirzaei, M Yunesian, Ar Mesdaghinia, S Nasseri, M Gholami, E Jalilzadeh, Sh Shoeibi,
Volume 11, Issue 3 (12-2018)
Abstract
Background and Objective: Antibiotics are a group of emerging contaminants in the aquatic environment. Antibiotic residues threaten the human health and ecosystem in the low concentrations found in the environment. Hence, the present work has been conducted to investigate the occurrence and removal efficiency of most prescribed antibiotics including amoxicillin, penicillin, cefixime, cephalexin, ciprofloxacin, erythromycin and azithromycin detected in two urban wastewater treatment plants (WWTPs) in Tehran.
Materials and Methods: The present work is an applied research based on USEPA method no. 1694, to investigate pharmaceuticals residues in water by HPLC/MS/MS in year 2016. The differences between target antibiotics residues were investigated statistically. After the calculation of the removal efficiencies, the normality of the data was assessed. Then, parametric and non-parametric tests were used to compare the removal efficiencies in both WWTPs.
Results: There was not a significant difference between the influent and effluent concentrations of cefixime and azithromycin (in Ekbatan WWTP) and cefixime (in southern Tehran WWTP). There is a significant difference between the removal efficiencies of cephalexin (p=0.005) and erythromycin (p=0.002) in two WWTPs. The Highest median removal efficiencies were observed for cephalexin 94.41 and 99.47 in Ekbatan WWTP and southern Tehran WWTP, respectively.
Conclusion: In addition to the type of treatment processes, it is physicochemical properties of the selected compound has a significant influence on removal efficiencies.
Mahdi Hadi, Alireza Mesdaghinia, Simin Nasseri, Elnaz Iravani,
Volume 13, Issue 4 (2-2021)
Abstract
Background and Objective: The bibliometric analysis is the most effective way to study the scientific output and trend of research. The purpose of this study is to analyze the scientific output of the Institute of Environmental Research (IER) at Tehran University of Medical Sciences using bibliometric technique.
Materials and Methods: All related IER articles that have been indexed in Scopus and WoK were retrieved from the beginning of 2009 till November 23, 2019. The bibliometric data were extracted and analyzed using R software.
Results: The document production follows an increasing exponential trend with a rate of 10% per year. 807 documents were retrieved with an average citations of 19.26 per each document. The documents per author and authors per document were obtained 0.196 and 5.1, respectively. The highest citations to documents was in 2017 (35.5 citations). The most frequent keywords were found “Adsorption”, “Drinking water”, “Air pollution”, “Particulate matter”, “Risk assessment” and “Response surface methodology”. Thus, engineering-based studies are more prominent in the published studies. Health-based studies, including risk assessment studies, accounted for the most area of research. The largest numbers of international research collaboration were recorded with the United States, Switzerland, Canada and India. While, in the national scale, Shahid Beheshti University of Medical Sciences’ collaboration was prominent.
Conclusion: It is still necessary to promote the level of the IER’s international collaborations to raise its regional status. In addition, more attention should be paid to health-based topics like risk assessment studies. These studies need to be given higher priority in the action plan of the IER’s centers and research groups.
Narges Lasemi, Mahdi Hadi, Simin Nasseri,
Volume 13, Issue 4 (2-2021)
Abstract
Background and Objective: One of the most important factors affecting communities’ health is safe drinking water. The UN general assembly considers “ensure availability and sustainable water and sanitation for all “as one of the 17 goals of SDGs for the 2030 development agenda. Target 6.1 of SDGs aims to provide universal and equitable access to affordable drinking water and to provide safe drinking water for all households. Target 6.2 calls for an end to defecation in an open environment to ensure that each person has access to the toilet and safe disposal system. In current study, 143 Savadkooh villages with defects in water supply systems and health services were selected to update the indicators and implement sustainable development goals.
Materials and Methods: A checklist was designed to extract targets 6.1 and 6.2 based on the Joint Monitoring Program (JMP). Considering 7400 households, margin of error of 5%, confidence limit of 95%, and the most conservative mode for response distribution (50%), the sample size was determined (512 households). Samples were collected randomly from all villages and then analysis was performed by SPSS 19.
Results: In drinking water sector, 84% of people have access to safe services, while only 15% and 1% have access to basic services and unimproved services, respectively. In sanitation sector, 98.8% of people use safe services though only 0.2% utilize limited services. In hygiene sector, 98.8% of people are provided with safe services.
Conclusion: Lack of drinking water safety and failure to improve water resources’ quality are the main problems in the drinking water sector. Lack of access to sewage network, wastewater disposal in the land is the biggest health hazard in the region. This study can provide solutions to improve the health quality of affected community.
