Showing 58 results for Adsorption
F Rezaei, G Moussavi, A.r Riyahi Bakhtiari, Y Yamini,
Volume 8, Issue 4 (3-2016)
Abstract
Background and Objectives: Adsorption is one of the most common methods for VOCs elimination from waste air stream. The study on the application of a selective and cheap adsorbent with high efficiency in VOCs removal is important from economic aspects. In this study, the potential of MnO/GAC and MgO/GAC composites was investigated for toluene adsorption from air stream at lab scale.
Material and methods: The MnO/GAC and MgO/GAC adsorbents were prepared through Sol-gel method and then were characterized using BET, XRF, and SEM analysis. The effect of operational parameters including; retention time (0.5, 1, 1.5, 2, and 4 S), inlet toluene concentration (100, 200, 300, and 400 ppmv) and the temperature of the air stream (25, 50, 75, and 100 ˚C) were examined on the efficiency of both adsorbents. The efficiency of MnO/GAC and MgO/GAC were determined from the breakthrough time and adsorption capacity and the results were compared statistically.
Results: The breakthrough time of MnO/GAC and MgO/GAC adsorbents increased 90% by increasing retention time from 0.5 to 4 S. Adsorption capacity of MgO/GAC and MnO/GAC was increased 39and 61.1% by increasing inlet toluene concentration from 100 to 400 ppmv, respectively. Breakthrough time of MgO/GAC and MnO/GAC decreased 65 and 59% by increasing inlet toluene concentration from 100 to 400 ppmv, respectively. The efficiency of MgO/GAC and MnO/GAC adsorbents had a direct relationship with the increase of air temperature from 25 to 100 ˚C. Accordingly, the efficiency of MgO/GAC and MnO/GAC was increased 78 and 32% by increasing air temperature, respectively.
Conclusion: The results of the study showed that MgO/GAC and MnO/GAC adsorbents had high efficiency in toluene removal from air stream. The difference between the efficiency of MgO/GAC and MnO/GAC adsorbents was significant and MgO/GAC adsorbent showed higher efficiency than MnO/GAC for toluene adsorption from waste air.
S Sobhanardakani, R Zandipak,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objective: Dyes are important pollutants that lead to producing serious hazards to human, other animals and organisms. Dyes are not biodegradable by aerobic treatment processes. Therefore, their removal from industrial effluents before discharging into the environment requires extreme and great attention. The aim of this research was to evaluate removal efficacy of methyl orange dye from aqueous solutions using NiFe2O4 nanoparticles.
Materials and Methods: This study was an empirical investigation in which NiFe2O4 nanoparticles were synthesized by co-precipitation method and were used as an adsorbent for the removal of methyl orange from aqueous solution. NiFe2O4 nanoparticles were characterized using X-Ray Diffraction (XRD), Transmission Electronic Microscopy (TEM), pHpzc and SEM-EDX elemental analysis methods. Experiments were conducted discontinuously using 20 mL methyl orange solution of 40 mg/L. The effect of variables such as pH (2-8), amount of adsorbent (0.009-0.07 g) and contact time (2-70 min) on the efficacy of dye removal was studied. Finally, experimental data were compared by Langmuir, Freundlich, and Temkin isotherms and pseudo-first-order and pseudo-second-order kinetic models.
Results: TEM images showed that the NiFe2O4 nanoparticles had spherical shapes with the size of 12 nm. The results indicated that removal efficiency increased up to 0.04 g adsorbent and 20 min contact time. The optimum pH for methyl range removal was 2. Moreover, under these conditions, the adsorption process followed the Langmuir adsorption isotherm with a correlation coefficient of 0.995 and pseudo-second-order kinetic model with a correlation coefficient of 0.999. Also, the maximum adsorption capacity of the prepared adsorbent was 135 (mg/g) for Langmuir isotherm.
Conclusion: The NiFe2O4 nanoparticles are effective and available adsorbents for the removal of methyl orange from industrial wastewater.
S Dehestaniathar, Sh Amini, A Maleki, B Shahmoradi, N Reshadmanesh, P Teymouri,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objectives: Fluoride has both beneficial and detrimental effects on health. Therefore, it is important to determine its concentration in drinking water. Dental fluorosis and skeletal fluorosis are health effects caused by long term exposure to high levels of fluoride in drinking water. The aim of this research was to investigate fluoride removal using modified diatomite-supported ferric oxide nanoparticles and to determine the adsorption kinetics and isotherm.
Materials and Methods: This fundamental and practical study was performed at laboratory scale. The effects of pH (3.5-9.5), contact time (20-100 min), adsorbent dosage (1-5 g/L), and initial concentrations of fluoride (5-25 mg/L) on the adsorption efficiency were evaluated. The properties of adsorbent were investigated using XRD, XRF, FTIR and FESEM. Finally, the suitability of pseudo first and second order kinetics, and Langmuir and Freundlich isotherms for the data were investigated.
Results: This study showed that the removal efficiency of F- increased with increase in contact time, decrease in pH, increase in adsorbent dose, and increase in initial fluoride concentration. The highest removal efficiency was observed at pH=3.5, 60 minutes contact time, and 3 g/L of adsorbent dose in the initial concentration of 5 mg/L F-. Pseudo first order and Freundlich were the best fitted kinetic and isotherm models, respectively, for describing F- adsorption process.
Conclusion: The present study indicates that the modified diatomite-supported ferric oxide nanoparticles can be used as an effective and environmentally friendly biosorbent for the removal of fluoride ions from aqueous solutions.
Z Rahmani, M Harati, Mr Rahmani, Y Poureshgh, Mt Samadi,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objective: Surfactants can be found in soaps, detergents, pharmaceutical products, personal care products, as well as in leather industries. In this study, adsorption of Sodium Dodecyl Sulfate (SDS) on magnetic multi-walled carbon nanotubes in the aqueous solutions was investigated.
Materials and methods: Surfactant concentration, adsorbent dosage, and pH values were considered as variables. Residual surfactant was measured using methylene blue method and adsorbent characteristic was determined by X-Ray diffraction and Fourier transform infrared spectroscopic analysis. Adsorption capacity, adsorption isotherm, and kinetic reaction were also investigated.
Results: Adsorption investigations demonstrated that the increase in initial SDS concentration or pH values, led to the decrease in SDS adsorption. Conversely, the same result was achieved by decreasing adsorbent dosage. After 120 min SDS adsorption became stable. By increasing in SDS concentration from 15 to 150 mg/L, adsorption capacity improved from 8 to 61 mg/g. Isotherm and kinetic data demonstrated that experimental data pursued Langmuir isotherm (R2=0.993) and pseudo-second order equation (R2=0.992).
Conclusion: Magnetic multiwall carbon nanotubes can be used as an effective and useful sorbent for SDS removal due to several advantages including: high adsorption capacity, relatively low equilibrium time, and easy separation of magnetic multiwall carbon nanotubes from aqueous solutions.
M Nourinejad, N Arsalani, H Namazi,
Volume 10, Issue 1 (6-2017)
Abstract
Background and Objective: Nicotine as the most toxic alkaloid in tobacco is one of the compounds which causes human death over the past few decades. The purpose of this paper was to remove nicotine environmental pollution from aqueous solutions using halloysite-polythiophene nanocomposite.
Materials and Methods: Halloysite-polythiophene nanocomposite was prepared using a homogeneous solution of HNT and FeCl3 at 0-5°C by the ball milling technique. In this study, parameters such as pH, contact time and initial concentration of nicotine in laboratory scale were studied and the physical properties of the adsorbent were characterized via fourier transform infrared (FTIR) and scanning electron microscopy (SEM). Then, the absorption results were described using Langmuir and Freundlich isotherms.
Results: The results showed that the pH, initial concentration of nicotine and contact time had a direct effect on the nicotine adsorption process. The adsorption of nicotine followed Langmuir isotherm (R2 < 0/995). Moreover, the best adsorption result was achieved at pH=7, 50mg adsorbent, contact time of 90 min and 50mg/L of nicotine.
Conclusion: The results of this study showed that the Halloysite modification as a mineral composite with polythiophene and the synthesis of HNT@PTh nanocomposite can be used as an effective adsorbent to adsorb the nicotine.
Y Azimzadeh, N Najafi, A Reyhanitabar, Sh Oustan,
Volume 10, Issue 1 (6-2017)
Abstract
Background and Objective: Phosphorus (P), as one of the agricultural, industrial and urban wastewater pollutants, plays an important role in eutrophication of surface waters. Use of cationic sorbents for removal of anions including phosphate from aqueous environments is a well-known and effective method. Meanwhile, layered double hydroxides (LDHs) are known as effective anion exchange sorbents. In this study, the efficiency of Mg-Al layered double hydroxide (Mg-Al-LDH) for P removal from aqueous solutions was investigated.
Methods and Materials: The Mg-Al layered double hydroxide (Mg-Al-LDH) was synthesized by co-precipitation method and used for removing of P from aqueous solutions. The kinetics and equilibrium studies of phosphate adsorption by Mg-Al-LDH were performed using a batch experiment at different contact times, initial phosphate concentrations, pH values, ionic strengths and doses of sorbent.
Results: The results of the kinetics experiments showed that sorption of P with LDH reached equilibrium after 30 min. The highest correlation coefficient was obtained for the pseudo-second order model, indicated that chemical sorption controlled the rate of phosphate sorption by LDH. The results showed that the sorption experiments data were in good agreement with Langmuir model and the maximum adsorption capacity predicted by this model was 37.83 mg P/g LDH.
Conclusion: The current study revealed that P adsorption by LDH was increased by increasing contact time and concentration of LDH, but decreased by increasing initial concentration of P, pH and ionic strength. The optimum conditions for phosphate anion adsorption by Mg-Al-LDH were determined as P initial concentration of 20 mg/L, contact time of 120 min, pH of 3.0, sorbent dose of 10 g/L and ionic strength of 0.03 mol/L.
P Baratpour, G Moussavi, A Alahabadi, E Fathi, S Shekoohiyan,
Volume 10, Issue 2 (9-2017)
Abstract
Background and Objective: With industrial development and population growth, the emerging contaminants enter into the natural water resources. Therefore, adsorption potential of Ammonium Chloride-induced activated carbon (NAC) to remove metolachlor pesticide from contaminated water was investigated in this study.
Materials and Methods: The effects of operational conditions including solution pH, NAC concentration, metolachlor initial concentration and contact time on the removal of metolachlor by Ammonium Chloride-induced activated carbon (NAC) and standard activated carbon (SAC) were studied.
Results: Over 92.4% of 50 mg/L metolachlor was adsorbed using 0.3 g NAC/L within 5 min, and by increasing the reaction time to 60 min the removal efficiency reached to 100%. Under similar experimental conditions, standard activated carbon (SAC) could only adsorb 20% of metolachlor within 5 min and increase of contact time to 40 min caused the improvement of metolachlor adsorption onto SAC to 48%. The adsorption onto SAC was not influenced by the contact time over 40 min. Kinetic analysis showed that experimental adsorption data for both NAC and SAC were best fitted to the pseudo-second-order model. The maximum adsorption capacities of metolachlor onto NAC and SAC calculated by the Langmuir model were 344.8 and 238.1 mg/g, respectively.
Conclusion: Generally, these results showed that developed NAC was an efficient adsorbent with high removal efficiency for eliminating the halogenated pesticides from the contaminated water streams.
H Kamani, Ah Panahi, Sd Ashrafi, F Kord Mostafapour, Ns Omrani Gargari,
Volume 10, Issue 3 (12-2017)
Abstract
Background and Objective: Extreme use of antibiotics and discharging to the environment lead to serious consequences. Mesoporous silica such as MCM-41 material is widely used to absorb contaminants from the aqueous solution. The aim of this study was to evaluate mesoporous synthesis of MCM-41 and its efficacy for removal of the antibiotic cephalexin from aqueous solution.
Materials and Methods: Physical characteristics and absorbent structure synthesized by techniques BET, FTIR and XRD were analyzed. The effect of variables such as pH values (3, 7, 11), the dose of MCM-41 (200, 500, 800 mg/L), initial concentration of cephalexin (50, 75, 100 mg/L), contact time (30, 60, 90 min), and process temperature (20, 30, 40 0C) on absorption of cephalexin were studied. In order to achieve the optimal experimental conditions, response surface methodology (RSM) model was used.
Results: The results showed that pH (p=0.0001), adsorbent dose (p=0.0001), initial concentration of cephalexin (p=0.0001), contact time (p=0.01), pH2 (p=0.0002) and pH (p=0.04) and initial concentration had a significant impact on the response variable. The optimum removal condition based on analysis of variance and the model was at the reaction time 90 min, pH 3, initial concentration 50 mg/L and adsorption dose 600 mg/L. Under these conditions, the removal efficiency of 81.1% was achieved.
Conclusion: The results showed that adsorption process with the mesoporous MCM-41 had a high efficiency on the removal of cephalexin from the aqueous environments.
M Ghodrat, E Asrari,
Volume 10, Issue 4 (3-2018)
Abstract
Background and Objective: Excessive consumption of antibiotics and the entrance of the potentially hazardous substances to the environment has become one of the environmental concerns. Today, adsorption is one of the efficient and reliable methods for the removal of this class of compounds. The aim of this study was to synthesize chitosan-Fe3O4 and to compare the efficacy of removing erythromycin antibiotics from aqueous humorous media by this adsorbent and chitosan.
Materials and Methods: The structural properties of the synthesized adsorbent were analyzed by TEM, PSA, VSM techniques. Various parameters including pH (1-11), contact time (0-60 min), adsorbent concentration (1-5 g/L), and initial concentrations of erythromycin (5-50 mg/L) was evaluated for the removal efficiency. For data analysis, Excel software was used. The equilibrium constant and the kinetic constants were calculated from the first-order kinetic model using Freundlich and Langmuir isotherms.
Results: The results indicated that increased pH and initial concentration of erythromycin increased the dose of adsorbents and the contact time of removal efficiency. The highest absorption efficiency at pH of 3 for both adsorbents, the contact time 30 min for modified chitosan and 50 min for chitosan, the dose of adsorbent 2 g/L for modified chitosan, and 3 g/L for chitosan and the initial concentration of erythromycin for each of the two adsorbents was 10 mg/L and the erythromycin adsorption by both adsorbents follows the Langmuir isotherm and the pseudo second order kinetics.
Conclusion: According to these results, chitosan modified with Fe3O4 can be used as a more effective adsorbent than chitosan for removal of erythromycin by adsorption method.
S Fallah Jokandan, M Yegane Badi, A Esrafili, A Azari, E Ahmadi, H Tarhandeh, M Kermani,
Volume 12, Issue 2 (9-2019)
Abstract
Background and Objective: The activities of various industries produce a wide range of pollutants and toxic compounds. One of these compounds is the catechol, a cyclic organic compound with high toxicity and resistant to degradation. Therefore, the purpose of this study was to investigate efficiency of powder activated carbon magnetized with Fe3O4 nanoparticles in the removal of catechol from aqueous solutions by response surface methodology.
Materials and Methods: The co-precipitation method was used to synthesize magnetic powder activated carbon and its properties were analyzed by SEM and XRD analysis. Then, the effect of the parameters such as pH, contact time, absorbent dose, initial concentration of catechol and temperature on the efficiency of adsorption process were investigated using a response surface methodology (Box–Behnken). The residual concentration of catechol was measured by HPLC at 275 nm.
Results: The results showed that the maximum efficiency of the adsorption process was obtained at concentration of 20 mg/L, pH=3, contact time 90 minutes, at 25 °C and absorbent dose of 1.5 g/L. The study of isotherm and kinetics showed that the experimental data of the catechol adsorption process correlated with the Langmuir and pseudo-second order models, respectively. Thermodynamic study of the reaction also expresses the Exothermic and Spontaneous process.
Conclusion: The results showed that the adsorption process using powder activated carbon magnetized with Fe3O4 nanoparticles at acidic pH had better efficiency. As a result, the studied process as an effective, rapid and inexpensive method for removal of catechol from aqueous solutions is proposed. Due to its short reaction time, it is economically affordable process.
H Niknejad, M Farzadkia, A Esrafili, M Kermani,
Volume 12, Issue 4 (2-2020)
Abstract
Background and Objective: 2,4 dinitrophenol is observed in sewage produced from chemical and petrochemical industries. Contamination of drinking water with these pollutants causes toxicity, health problems and change in taste and odor. The present study was developed to evaluate the efficiency of removal 2,4-DNP through dried sludge adsorbent and modified calcium chloride sludge adsorbent.
Materials and Methods: At first, sludge was dried at temperature of 60 °C. Next, CaCl2 was used to improve adsorption capacity. The removal efficiency of 2,4 dinitrophenol were determined by HPLC at wavelength of 360 nm. The effects of influencing factors including pH, initial pollutant concentration, contact time, and adsorbent dose were examined.
Results: The optimum pH of adsorption for both adsorbents was found to be 7. The optimum concentration of 2,4-DNP was 10 ppm. The results obtained from the present research showed that the removal of the contaminant using dried and modified sludge sorbent was increased from 72.6% to 86% at a dosage of 1.5 g. The adsorption kinetics were fitted with the pseudo second order kinetics model for both adsorbents. The isotherm data also showed that the adsorption of this pollutant on both adsorbents is fitted with the Freundlich model.
Conclusion: Results obtained from the present study indicated that the efficiency of the modified sludge ash is more than the non-modified sludge in 2,4 dinitrophenol removal. This can reduce adsorbent consumption in industrial treatment plants.
Azadeh Modiri, Shadab Shahsavari, Ali Vaziri Yazdi, Ali Akbar Seifkordi,
Volume 13, Issue 1 (4-2020)
Abstract
Background and Objective: Arsenic has long been considered as a heavy metal and toxic pollutant due to its potential to harm the human health and the environment. Adsorption is one of the mechanisms for arsenic removal from wastewater. Therefore, the purpose of this research was to investigate the feasibility of synthesized chitosan-zirconium magnetic nano fiber on arsenic adsorption from wastewater and to evaluate its kinetic and isotherm models.
Materials and Methods: Synthesis of nanofibers was performed by electrospinning method and the optimal formulation was determined following the experimental design. Then, kinetics and isotherms of arsenic adsorption on the as synthesized nanofibers were investigated. The prepared nanofiber was characterized using X-ray diffraction (XRD), Field Emission Scanning Electron Microscopes (FESEM), Infrared Fourier Transform (FT-IR) and Vibrational Sampler Magnetic Meter (VSM).
Results: The optimal formulation was obtained: 2.84% chitosan, 0.97% nano-zirconium and 0.94% nano-iron. The adsorption of arsenic on synthetic fibers was found to follow quasi-first-order kinetics and the Freundlich isotherm. Furthermore, the effect of initial concentrations of arsenic, contact time, temperature and pH on arsenic adsorption were surveyed. The optimal condition for nitrate arsenic adsorption was obtained at initial concentration of 70 mg/L, 45 min contact time and at pH 3.
Conclusion: According to the results, the synthesized nanofiber displayed a regular network structure with the distribution of the Zr-nanoparticles in its shape. Also, according to the form of magnetometric analysis, it was found that chitosan-nanosirconium magnetic nanofibers are well magnetized and are free magnetic. Finally, it can be concluded that the synthesized nanosorbent has a high potential for arsenic removal from industrial effluents.
Nahied Shahbodaghi, Daryoush Afzali, Maryam Fayazi,
Volume 15, Issue 1 (4-2022)
Abstract
Background and Objective: With increasing water pollution, serious water shortages and increased pressure to save water, recycling and reuse of water has attracted more attention in various industries. Removal of silica from cooling water is essential for recycling and reuse of water. The aim of this study was to remove silica from water using magnesium oxide nanoparticles (MgO) synthesized by chemical deposition method.
Materials and Methods: Synthetic nanoparticles were successfully determined using field emission scanning electron microscopy (FE-SEM), Fourier transform infrared (FTIR) and X-ray diffraction (XRD). To determine the optimal adsorption conditions the batch system, the effect of important parameters such as pH (2-8), contact time (0-150 min), initial concentration of silica solution (50-1000 mg/L), adsorbent amount (0.01-0.14 g) and temperature (25-60 ˚C) were studied.
Results: Under optimal conditions, an almost removal of 200 mg/L silica solution was achieved in 60 min reaction time. Equilibrium data were analyzed using the Langmuir and Freundlich isotherms. The adsorption process can be well described by the Langmuir model, and the maximum adsorption capacity was calculated as 75.76 mg/g. Synthetic data were analyzed using pseudo-first-order and pseudo-second-order equations. The pseudo-second-order model showed good agreement with the obtained data (R2 = 0.9949).
Conclusion: Due to the high potential of magnesium oxide nanoparticles in silica removal, it can be a good candidate for the removal of silica and industrial wastewater treatment.
Mohammad Ghafoori, Mehrdad Cheraghi, Maryam Kiani Sadr, Bahareh Lorestani, Soheil Sobhanardakani,
Volume 16, Issue 2 (9-2023)
Abstract
Background and Objective: Antibiotics are emerging pollutants that enter the human environment through pharmaceutical, hospital, and urban wastewater. Therefore, this study was conducted to investigate of removal efficacy of tetracycline (TC) from aqueous solutions using GO@Fe3O4@β-CD.
Materials and Methods: In this descriptive study, GO@Fe3O4@β-CD was synthesized and then used as an adsorbent for the removal of TC from aqueous solution. GO@Fe3O4@β-CD was characterized using X-ray diffraction (XRD), Scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and vibrating sample magnetometry (VSM) methods. Also, the influence of variables including pH (3-9), amount of adsorbent (0.003-0.050 g), contact time (0-100 min), and temperature (25-55 °C) so assessed on the efficacy of TC removal.
Results: The results of TGA analysis showed that GO@Fe3O4@β-CD nanoparticles were resistant to temperatures up to 400 °C. Also, the results indicated that β-cyclodextrin was uniformly dispersed on the surface of GO@Fe3O4.
The results indicated that removal efficiency increased up to 60 min contact time, 0.01 g of adsorbent, and decrease temperature to 25 °C. The optimum pH for TC removal was 7.0. Also, under these conditions, the adsorption process followed the Langmuir adsorption isotherm with a correlation coefficient of 0.992 and the pseudo-second-order kinetic model with a correlation coefficient of 0.997, 0.999, and 0.998. The maximum adsorption capacity of the prepared adsorbent was 357 mg/g.
Conclusion: The GO@Fe3O4@β-CD could be an effective and efficient adsorbent for the removal of TC from industrial wastewater.
Mohammad Hossein Fekri, Samaneh Soleymani, Maryam Razavi Mehr, Fatemeh Saki,
Volume 16, Issue 2 (9-2023)
Abstract
Background and Objective: Due to the presence of industrial pollutants in water sources, it is necessary to treat wastewater, especially colored wastewater. This study aims to treat wastewater containing methyl orange dye using nano mesopore SBA-16.
Materials and Methods: In this study, the effect of different parameters (pH, concentration of methyl orange, amount of adsorbent, temperature, and contact time) on the absorption of methyl orange by nanocomposite prepared with the help of Design of Experiment 7 software and Response Surface Method (RSM) was investigated.
Results: The maximum amount of pollutant removal by the adsorbent was obtained under optimal conditions of pH = 4.07, temperature 50 °C, contact time 35 minutes, initial concentration of adsorbent 10 mg/L, and amount of adsorbent 0.04 g. Also, the findings showed that the absorption behavior is most consistent with the Langmuir isotherm and the absorption process is exothermic and spontaneous at low temperatures.
Conclusion: In optimal conditions, the SBA-16 adsorbent was able to remove 98.60 % of methyl orange from the aqueous solution and the maximum adsorption capacity (qmax) for the removal of methyl orange pollutant was 37.73 mg/g. Considering the high potential of nano mesopore SBA-16 in removing methyl orange pigment, it can be considered a suitable candidate for removing colored pollutants and treating wastewater from textile factories.
Mahboub Saffari,
Volume 16, Issue 3 (12-2023)
Abstract
Background and Objective: Nowadays, the use of biochar as a new and suitable adsorbent to remove inorganic pollutants from water sources has grown significantly. The present study was conducted to evaluate the effects of biochar physical modifications compared to unmodified biochar on nickel (Ni) removal efficiency in aqueous solutions.
Materials and Methods: After the production of cypress cones biochar (RB), biochar particles (<164 µm) were crushed into very small (<26 µm) dimensions (BMB) using a planetary ball mill and after evaluation their various properties by SLS, BET, FTIR and SEM techniques, their application (RB and BMB) in optimizing the Ni removal from aqueous solutions were evaluated using the response surface methodology (RSM: Box-Behnken design).
Results: Based on the results, the physical modification of biochar (BMB) decreased the particle size by 6.2 times, increased the specific surface area by 4.9 times, increased (containing oxygen) and decreased (aliphatic and OH stretching groups) of specific functional groups and finer surface morphology, compared to RB. The use of BMB in the aqueous solution caused an increase of 9.7% (on average) in the removal of Ni compared to the RB sample. The fitting of the data obtained from Ni removal in the Box-Benken model in both adsorbents shows the appropriate prediction of this model in the optimization of Ni removal from aqueous solutions.
Conclusion: According to the results of this research, the physical modification of biochar, as a simple, cheap, and environmentally friendly method, due to the increase in the efficiency of Ni pollutant removal, can be introduced as a suitable method in the activation of biochar, which further research is required based on the type of biochar and various pollutants.
Yadollah Yousefzadeh, Vida Izadkhah, Soheil Sobhanardakani, Bahareh Lorestani, Sedigheh Alavinia,
Volume 16, Issue 4 (3-2024)
Abstract
Background and Objective: Antibiotics as emerging pollutants are harmful to environmental health. Therefore, this study was conducted to investigate the efficiency of Uio-66-NH2@CS-Iso-Gu nanohybrid for the removal of amoxicillin (AMX) from aqueous solutions.
Materials and Methods: In this study, for the first time, guanidine and isocyanate monomers are cross-linked with chitosan. The combination of this polymer with organometallic compounds contributes to its chemical/thermal stability and reusability. Uio-66-NH2@CS-Iso-Gu nanohybrid was characterized using X-ray diffraction (XRD), Scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA), and BET methods. Also, the effects of pH, initial concentration of AMX, contact time, and temperature were evaluated. Moreover, isotherm, kinetic and thermodynamics studies were performed.
Results: The results of TGA analysis showed that Uio-66-NH2@CS-Iso-Gu nanohybrid was resistant to temperatures up to 400 °C. Also, optimal adsorption of AMX occurred in the first 25 min. The synthesized nanohybrid has a surface area of 101.2 m2/g and a type IV isotherm. Acidic groups were present on the synthesized nanohybrid surface based on the pHpzc = 4.7. Langmuir (for 25 °C and 45 °C) and Freundlich (for 65 °C) isotherm models and pseudo-second-order kinetic models are more appropriate to fit the adsorption data with the experimental data. The maximum adsorption capacity of the synthesized nanohybrid was equal to 56.49, 40.65, and 0.382 mg/g at temperatures of 25°C, 45°C, and 65°C, respectively. Based on the findings, Uio-66-NH2@CS-Iso-Gu nanohybrid could be used for up to five cycles without significantly reducing their performance.
Conclusion: The results showed that Uio-66-NH2@CS-Iso-Gu nanohybrid has a significant efficiency for removing AMX and could be used as an effective adsorbent for the treatment of wastewater containing pharmaceutical residues.
Omid Mohammadi Moinalzoafa, Maryam Tahmasebpoor,
Volume 17, Issue 4 (3-2025)
Abstract
Background and Objective: The global increase in energy consumption has led to a rise in carbon dioxide emissions, causing significant and often irreparable damages such as global warming. This study investigates the adsorption capacity of hairy nanocrystalline cellulose as a novel adsorbent and seeks to enhance its performance in carbon dioxide capture by modifying it with two types of amines: monoethanolamine and diethanolamine.
Materials and Methods: Hairy nanocrystalline cellulose was synthesized through oxidation and amine modification. The formation of chemical groups and sample morphology was analyzed using Fourier transform infrared spectroscopy and field emission scanning electron microscopy. Additionally, thermogravimetric analysis was performed at two temperatures (25 and 50 °C) and two concentrations (10% and 90% carbon dioxide in nitrogen) to evaluate the adsorption capacity of the samples.
Results: The results showed that at 25 °C and a carbon dioxide concentration of 90%, the adsorption capacities of hairy nanocrystalline cellulose, cellulose modified with 20% by weight of monoethanolamine, and cellulose modified with 20% by weight of diethanolamine were 1.74, 2.5, and 1.96 mmol/g, respectively. These findings indicate that modifying the adsorbent with monoethanolamine increased its carbon dioxide adsorption capacity by approximately 44%, while modification with diethanolamine resulted in a 13% improvement.
Conclusion: The findings suggest that hairy nanocrystalline cellulose, particularly in its modified forms, holds significant promise as a novel and effective adsorbent for carbon dioxide capture.
