Iranian Journal of

---

Backgrounds and Objectives: Anthraquinone dyes such as reactive blue29 in water resources and industrial wastewater effluents are one of the most environmental setbacks in many countries. Various methods have been considered to remove these dyes One of which is adsorption.
Materials and Methods: All adsorption experiments were conducted in different pHs and various concentrations of adsorbents. The initial concentration of reactive blue 29 chosen in this study was 30mg/L.Adsorption isotherms were determined and correlated with Longmuir, Freundlich and BET models.
Results: The maximum adsorption capacity of reactive blue 29 onto single wall carbon nanotubes was 496mg/g.Results showed that the best pH for adsorption was 5 followed by pH3 and 8. Kinetic study showed that the equilibrium time for adsorption of RB 29 to SWCNT is 4 hr.
Conclusion:According to the results obtained BET isotherm fitted well the experiment. It shows the adsorption of reactive blue 29 onto single wall carbon nanotubes is multilayers and the mechanism of SWCNTs adsorption toward RB29 is based on weak van der waals forces.

---

Background and objectives: Bisphenol A (BPA) is an endocrine disrupting chemical that releases to the environment through effluents of its producing factory, pulp and paper mill factories, and plastics industry. The purpose of this study was to investigate adsorption isotherms of removing BPA from aqueous solutions using single walled carbon nanotubes (SWCNTs). Materials and methods: This study was an empirical investigation. Our experiments were conducted discontinuously using 50 mL of sample in each test. The variables of this study were the contact time (5, 15, 30, 60, 90, 120 min), the initial concentration of BPA (2, 5 , 20, 50 mg/L), and pH (3, 5, 6, 9, 11). The concentrations of BPA were measured using UV-Vis spectrophotometer. Results: The maximum adsorption capacity was found to be 71.42 mg/g. The results of our experiments showed that maximum adsorption capacity at equilibrium was achieved at t = 60 min and pH = 9. Moreover, increasing the initial concentration is associated with an increase in adsorption capacity until it becomes constant. Conclusion: The BPA adsorption on SWCNT follows Freundlich-Langmuir isotherm.

---

Background and Objective: Various industries such as petrochemical, oil refinery, pharmaceutical, plastics, paper, steel and, resin produce a substantial of phenol and its derivatives. Wastewaters containing phenol need careful treatment before discharging into the environment due to their poor biodegradability and high toxicity. The objective of this study was to remove phenol by multiwall carbon nanotubes from aqueous solution. Materials and Methods: Adsorption process was implemented in a laboratory-scale batch with emphasis on the effect of various parameters such as contact time (5 to 120 minutes), pH (3- 11), initial concentration of phenol (5 - 50 mg/l) and the sulfate and chloride ions (20 - 200 mg/l) on adsorption process. To achieve a better realization of adsorption process, sorption kinetics and equilibrium isotherms were also determined. Results: The results indicated that maximum adsorption capacity occurred at concentration 50 mg/L and t =30 minutes. The uptake fluctuated very little in the pH range of 3–9, and at greater than 9 the absorption decreased suddenly. Moreover, the presence of sulfate and chloride ions had no effect on the process. It was found that adsorption kinetics and equilibrium data follow a pseudo-second-order kinetics model and a Freundlich isotherm model respectively. Conclusion: It is concluded that carbon nanotubes being effective in a wide range of pH, short time to reach equilibrium and the absence of competing ions on the absorption process can be used effectively in removing phenol from aqueous solution.

---

Background and Objective: Phenol and phenol derivatives in industrial wastewater are among the pollutants with priorities. The high cost and low efficiency of some routine treatment processes of industrial wastewater has limited their use. One of the new methods under consideration is, nowadays, adsorption using carbon nanotubes. This study was conducted in order to evaluate the application of alumina-coated multiwall carbon nanotubes in eliminating phenol from synthetic wastewater. Materials and Methods: This study was performed in laboratory at batch scale. Multi-wall carbon nanotubes were coated with Alumina. The concentration of phenol was determined by spectrophotometer through photometry. The effect of pH changes, dosage of adsorbent, contact time, the initial concentration of phenol, temperature, and the concentrations of different salts on the efficiency of absorption was evaluated. Then, the absorption results were described using the Langmuir and Freundlich isotherms and the synthetics of absorption. Results: It was found that absorption efficiency increased significantly by decreasing the initial concentration of phenol and pH and by increasing the carbon nanotube dosage, temperature, and contact time. On the other hand, the maximum elimination of phenol from the solution (98.86%) occurred at 4 mg/l phenol concentration, under acidic conditions (pH=3), at adsorbent dosage of 0.05 g/l, at temperature of 45°C, and contact time of 10 min. Evaluation of the regressions isotherms showed that the process follows the Langmuir model and second-degree synthetic absorption. Conclusion: The high efficacy (98%) of the adsorption process in this study showed that alumina-coated multiwall carbon nanotubes have a good capability in eliminating phenol and can be used as an appropriate and new method for eliminating phenol and its derivatives from wastewater.

---

Background and Objective: Natural organic matters (NOMs) are a mixture of chemically complex polyelectrolytes with varying molecular weights, produced mainly from the decomposition of plants and animal residues. Various purification methods are used for removal of NOMs from water. The objective of this study was to remove NOMs from aqueous solution using reformed continuous carbon nanotubes column. Materials and Methods: The removal of NOMs from aqueous solution using reformed continuous carbon nanotubes column was studied. Effect of several variables such as zero point of pH (pH_ZPC), pH, influent concentration of natural organic matters were studied and different isotherms were assessed. Results: Investigation of pH effect showed that the adsorbability of NOMs increased with decreasing of pH. The experiments indicated that carbon nanotubes (CNT) samples exhibit pH_ZPC around 6. Results from Freundlich, Langmuir, and BET isotherm experiments revealed that the correlation coefficient R² in Freundlich model was higher than that of Langmuir. In addition, experiments of continuous flow in different initial concentrations of NOMs showed that the adsorption capacities of CNT were 53.46, 30.40, and 24.75 mg/g for NOMs initial concentrations of 10, 5, and 3 mg/L, respectively. Conclusion: The present study shows that CNTs have high potential for adsorption of NOMs from aqueous solution

---

Background and Objective: Surfactants can be found in soaps, detergents, pharmaceutical products, personal care products, as well as in leather industries. In this study, adsorption of Sodium Dodecyl Sulfate (SDS) on magnetic multi-walled carbon nanotubes in the aqueous solutions was investigated.

Materials and methods: Surfactant concentration, adsorbent dosage, and pH values were considered as variables. Residual surfactant was measured using methylene blue method and adsorbent characteristic was determined by X-Ray diffraction and Fourier transform infrared spectroscopic analysis. Adsorption capacity, adsorption isotherm, and kinetic reaction were also investigated.

Results: Adsorption investigations demonstrated that the increase in initial SDS concentration or pH values, led to the decrease in SDS adsorption. Conversely, the same result was achieved by decreasing adsorbent dosage. After 120 min SDS adsorption became stable. By increasing in SDS concentration from 15 to 150 mg/L, adsorption capacity improved from 8 to 61 mg/g. Isotherm and kinetic data demonstrated that experimental data pursued Langmuir isotherm (R²=0.993) and pseudo-second order equation (R²=0.992).

Conclusion: Magnetic multiwall carbon nanotubes can be used as an effective and useful sorbent for SDS removal due to several advantages including: high adsorption capacity, relatively low equilibrium time, and easy separation of magnetic multiwall carbon nanotubes from aqueous solutions.

---