Showing 27 results for Isotherm
H. Asilian, G.r Moussavi, M. Mahmoudi,
Volume 3, Issue 1 (4-2010)
Abstract
Backgrounds and Objectives:Much attention has been recently paid on using waste materials as adsorbents for removal of contaminants from water and wastewater. A new low cost waste was examined for its capacity to adsorb RR198, an azo reactive model dye, from an aqueous solution.
Materials andMethods: The waste was dried, powdered and characterized before being used as an adsorbent. The effects of pH (3-10), adsorbent dose (0.2-3 g), dye concentration and contact time on the adsorption efficiency were investigated. Equilibrium study data were modeled using Langmuir and Freundlich models.
Results: The characterization analysis indicated that itwas composedmainly of ferric hydroxide. The powder had a BET and average pore size of 107 m2/g and 4.5 nm, respectively. The results showed that dye removal was highest at a solution pH of 7 to 8 and a powder dose of 2 g/L. The RR198 removal percentage decreased from 100& to 43& at 140 min contact time when the concentration of dye was increased from 25 mg/L to 100 mg/L, at optimum pH and dosage. The Langmuir equation provided the best fit for the experimental data. The maximum adsorption capacity was calculated to be 34.4 mg/g.
Conclusion: According to the obtained results, the water coagulation waste sludge appears to be a suitable low cost and effcient adsorbent for removing reactive azo dyes from waste streams.
A Maleki, A Eslami,
Volume 3, Issue 4 (1-2011)
Abstract
Backgrounds and Objectives:Water contamination with arsenic has been recognized as a serious problem and its epidemiological problems to human health have been reported. The objective of this study was to explore the possibility modified wheat straw using sodium bicarbonate for removing arsenic from aqueous solution.
Materials and Methods: Adsorption process was accomplished in a laboratory-scale batch with emphasis on the effect of various parameters such as pH, contact time, arsenic concentration and adsorbent dosage on adsorption efficiency. In order to understand the adsorption process, sorption kinetics and equilibrium isotherms were also determined.
Results: It was found that adsorption of the arsenic was influenced by several parameters such as arsenic initial concentration, adsorbent dosage and solution pH. Maximum absorption efficiency was achieved at pH 7. As expected the amount of arsenic adsorbed on wheat straw incresed as its concentration went up. Among the models tested, namely the Langmuir, Freundlich, and Dubinin Radushkevich isotherms, the adsorption equilibrium for arsenic was best described by the Langmuir and Freundlich models. It was also found that adsorption of arsenic by wheat straw followed pseudo second-order kinetics. Mean free energy of adsorption (15.8 kJ mol-1) indicates that adsorption of arsenic by wheat straw might follow a chemisorption mechanism. Desorption studies show that arsenic ions are strongly bounded with the adsorbent and exhibit low desorption.
Conclusion: It is concluded that that adsorption by modified wheat straw is an efficient and reliable method for arsenic removal from liquid solutions.
K Naddafi, R Nabizadeh Nodehi, M Jahangiri Rad,
Volume 3, Issue 4 (1-2011)
Abstract
Backgrounds and Objectives: Anthraquinone dyes such as reactive blue29 in water resources and industrial wastewater effluents are one of the most environmental setbacks in many countries. Various methods have been considered to remove these dyes One of which is adsorption.
Materials and Methods: All adsorption experiments were conducted in different pHs and various concentrations of adsorbents. The initial concentration of reactive blue 29 chosen in this study was 30mg/L.Adsorption isotherms were determined and correlated with Longmuir, Freundlich and BET models.
Results: The maximum adsorption capacity of reactive blue 29 onto single wall carbon nanotubes was 496mg/g.Results showed that the best pH for adsorption was 5 followed by pH3 and 8. Kinetic study showed that the equilibrium time for adsorption of RB 29 to SWCNT is 4 hr.
Conclusion:According to the results obtained BET isotherm fitted well the experiment. It shows the adsorption of reactive blue 29 onto single wall carbon nanotubes is multilayers and the mechanism of SWCNTs adsorption toward RB29 is based on weak van der waals forces.
Y Hamzeh, S Izadyar, E Azadeh, A Abyaz, Y Asadollahi,
Volume 4, Issue 1 (5-2011)
Abstract
Background and Objectives: The dyestuff manufacturing and textile industries consume a high volume of water and produce a great amount of wastewater containing various toxic substances. Different methods are used to remove dye compounds from wastewaters. Removal of dyes from water by adsorption processes received considerable attention and a number of studies focused on the adsorption of some dyes by non-conventional low cost and effective adsorbents. In this study, the suitability of the canola stalks for Acide orange 7 adsorption was assessed.
Materials and Methods: The dry canola stalks obtained from the research farm were milled and screened and the particles size ranged between 0.4-0.7mmwere used in all experiments. Acid orange 7 supplied by Alvan Sabet. Initially, the effects of initial dye concentration, pH and temperature on adsorption were examined. The kinetic and equilibrium data obtained for various concentrations of evaluated on the basis of Langmuir and Freundlich isotherms.
Results: The results showed that the absorption efficiency depended strongly on pH and slightly on the temperature. Absorption of acid orange 7 on the canola stalks was fairly rapid and more than 95% of adsorption occurred within the initial 5 minutes of the treatment. Both Langmuir and Freundlich models were applicable for the description of acid orange 7 dye adsorption by canola stalks.
Conclusion: According to the Langmuir model, the highest capacity of canola stalks for acid orange 7 adsorption was found 24.8 mg/g which was higher than the capacity of beech wood sawdust and soil mixture with fly ash.
R Shokohi, M.r Samarghandi, F Pourfarzi, M Shirzad Siboni, H Vahedi,
Volume 4, Issue 1 (5-2011)
Abstract
Background and Objectives: Industrial wastewater included the dyes one of the important sources of environmental pollution, that founded in loom wastewater which are harmful for human health and environment. Therefore, the purpose of this research was investigated removal of RB5 dye from aquatic solution by using of adsorption onto synthesized magnetic sodium alginate beads.
Material and Methods: At first, synthesized magnetic sodium alginate beads. Then, acquired beads optimum dosage equal to 18 g/100CC, with constant other parameters. The effect of pH, contact time and initial RB5 dye concentration was studied at the constant of beads (18 g/100CC).
Results: Results showed that removal efficiency was decreased by increasing of initial RB5 dye concentration. Also the results showed the removal efficiency was increased by increasing of adsorbent dose and contact time. The results showed data were explained acceptably by Langmuir isotherms and pseudo-second-order kinetics models respectively.
Conclusion: The results showed that removal of RB5 dye from aqueous solution by using of magnetic sodium alginate beads can be done cheaper and effective.
Majid Kermani, Mitra Gholami, Abdolmajid Gholizade, Mahdi Farzadkia, Ali Esrafili,
Volume 5, Issue 1 (4-2012)
Abstract
MicrosoftInternetExplorer4
Background and Objectives: Phenols in trace quantities are usually present in the treated
effluent of many wastewater-treatment plants. Phenol compounds even at low
concentration can cause toxicity, health and significant taste and odor problem
in drinking waters. This research focuses on understanding the sorption process
and developing a cost-effective technology for the treatment of water
contaminated with phenolic compounds, which are discharged into the aquatic
environment from a variety of sources. In order to remove phenolic compounds
from water, a new natural sorbent, rice husk ash, was developed.
Materials and Methods: Removal of phenol, 2-chlorophenol and 4-chlorophenol were characterized by
spectrophotometric technique at wavelengths of 269.5, 274 and 280 nm,
respectively, under batch equilibrium conditions and via changing the
parameters of contact time, initial pH, and initial concentration of adsorbates
and dosages of sorbent. Finally, the results were analyzed by the kinetic and
isotherm models.
Results: in this
study, the equilibrium time was found to be 240 min for full equilibration of
adsorbates. Removal percent of 2-chlorophenol was lower than two others. The
maximum removal of phenol, 2-CP and 4-CP was observed at an initial pH of 5.
The percentage removal of these phenolic compounds increased with increasing
adsorbent dose and decreasing initial concentration. In kinetics studies,
correlation coefficient and ARE factor showed that the sorption of phenol
(R2=0.9999), 2-chlorophenol (R
2=0.9992) and 4-chlorophenol (R
2=1)
fitted by pseudo second order model. Isotherm studies also revealed that,
Langmuirmodel for phenol (R
2=0.9499), Freundlich model for
2-chlorophenol (R
2=0.9659) and 4-chlorophenol (R
2=0.9542)
were the best choices to describe the sorption behaviors.
Conclusion: Sorption
process is highly dependent on the pH and it affects adsorbent surface
characteristics, the degree of ionization and removal efficiency. At high pH
hydroxide ions (OH-)
compete for adsorption sites with phenol molecules. The sorption was done
rapidly and a plateau was reached
indicating the sorption sites occuupied till
they were saturated. Since the increasing sorbent dose would improve
sorption site, its increasing enhances phenolic compounds removal.
!mso]>
ject classid="clsid:38481807-CA0E-42D2-BF39-B33AF135CC4D" id=ieooui>
Afshin Maleki, Amir Hossein Mahvi, Reza Rezaee, Behrouz Davari,
Volume 5, Issue 4 (2-2013)
Abstract
Background and Objectives: Dyes are an important class of pollutants, which can even be identified by naked eye. Disposal of dyes in precious water resources have been prohibited, however, various treatment technologies are in use. Among various methods adsorption occupies a prominent place in dye removal. Therefore, natural zeolite (clinoptilolite) and acid modified zeolite were used as a low-cost adsorbent to evaluate their ability to remove color from aqueous solution using a batch adsorption experiments.
Materials and Methods: Modification of zeolite surface was carried out with two acids sulfuric acid and phosphoric acid, to improve the removal efficiency of reactive blue 19. We studied the influence of acid concentration, contact time, solution pH, initial dye concentration, and adsorbent dosage on the removal efficiency.
Results: The parameters of Langmuir and Freundlich adsorption isotherms have been determined using the adsorption data. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. It was also found that adsorption of dye by zeolite followed pseudo first-order kinetics. The adsorption results indicated that natural zeolite has a limited adsorption capacity for reactive dye but can be distinctly improved by modifying its surfaces with acid. Experimental results also showed that sulfuric acid has better performance than phosphoric acid in the modification of zeolite for dye adsorption.
Conclusion: We achieved the best results in terms of removal efficiency (41-72%) for the zeolite modified with Si/Al ratio of 7.5 after 3 h of contact.
Hafez Golstanifar, Simin Nasseri, Amir Hossin Mahvi, Mohamad Hadi Dehghani, Anvar Asadi ,
Volume 5, Issue 4 (2-2013)
Abstract
Background and Objectives: The contamination of nitrate (NO3−) in groundwater resources causes two adverse health effects: induction of “blue-baby syndrome” (methemoglobinemia), especially in infants, and the potential formation of carcinogenic nitrosamines. The aim of this research is to investigate nitrate removal from groundwater using alumina nanoparticles and to determine the adsorption isotherms.
Materials and Methods: This analytical-descriptive study was carried out at lab-scale, under batch conditions, and at room-temperature. The structure of alumina nanoparticles was determined using XRD, SEM, and TEM techniques. The concentration of nitrate in the solutions was determined by spectrophotometer at wavelengths of 220 and 275 nm. In addition, we investigated the impact of the important operational parameters including initial dose of Al2O3 (0.06-0.25 g/l), initial concentration of the solution (50- 300 mg/l), contact time (5-60 min), and pH (3-9). Moreover, we used Freundlich and Langmuir isotherm models to calculate equilibrium constant.
Results: It was found that nitrate removal efficiency increased as we increased contact time, initial concentration and pH in batch system. A maximum of 60% nitrate removal was achieved under following conditions: 60 min contact time, pH 5, and initial nitrate concentration of 300 mg/l as N. The obtained results showed that the adsorption of nitrate by Nano-Gamma-Alumina follows Langmuir isotherm equation with a correlation coefficient equal to 0.982.
Conclusion: Overall, our findings showed that the alumina nanoparticles can be used as an effective adsorbent to remove NO3 from aqueous solutions.
Ali Reza Rahmani, Ghorban Asgari, Mehrdad Farrokhi, Mahdi Shirzad Siboni,
Volume 5, Issue 4 (2-2013)
Abstract
Background and Objectives: Dyes are one of the main environmental pollutants in the industrial effluents including textile industries, which are harmful for human health and environment. The purpose of this research was to investigate removal efficiency of Reactive Black 5 (RB5) dye using adsorption onto strongly basic anion exchange resin as an appropriate adsorbent.
Materials and Methods: After preparing materials and equipment required, removal efficiency of Reactive Black 5 (RB5) dye using adsorption onto strongly basic anion exchange resin was investigated with respect to the variation of pH, contact time, adsorbent dosage, and initial RB5 dye concentration in batch system. Then results were analyzed using Excel software.
Results: Our results showed that removal efficiency was decreased by increasing pH and initial RB5 dye concentration. Moreover, we found that the removal efficiency was increased by increasing adsorbent dosage and contact time. The kinetics and equilibriums data were explained acceptably by Langmuir isotherms and pseudo-second-order kinetics models respectively.
Conclusion: Overall, our findings revealed that removal of RB5 dye from aqueous solution using adsorption onto strongly basic anion exchange resin can be considered as an effective and quick method.
Amir Sheikh Mohammadi, Mahdieh Sardar,
Volume 5, Issue 4 (2-2013)
Abstract
MicrosoftInternetExplorer4
Background
and Objectives: Antibiotics are
potential pollutants that represent an important environmental problem because
of their toxic effects on the food chain and aqueous streams. The objective of
this research was to study the adsorption of penicillin G on to chestnut shell
as an inexpensive adsorbent.
Materials and Methods: This study was performed at laboratory scale
and batch system. We studied the influence of process variables such as
adsorbent dose, initial PEN G concentration, pH of solution, contact time, and
breakthrough curves. In order to find out the possibility of reuse, desorption
study was also carried out. The surface characteristics of adsorbent were
investigated using Fourier Transform Infra-Red and Scanning electron
microscope. Equilibrium study data were modeled using Langmuir, Freundlich, and
D-R models. Moreover, kinetic studies
were done by three models of pseudo first order, pseudo second order, and
intra-particle diffusion.
Resuls: The maximum
PEN G removal achieved was 92%, at pH 3, adsorbent dose 0.1 g/l and contact
time 120 min. The Langmuir equation (R
2=0.99) provided the best fit
for the experimental data. It was also found that adsorption of PEN G by
chestnut shell followed pseudo- second order model (R
2= 0.992).
Conclusion: According to the results obtained, chestnut
shell appears to be a suitable, low cost and efficient adsorbent for removing
PEN G from waste streams.
Elnaz Iravani, Mohammadhadi Dehghani, Amirhossein Mahvi, Noushin Rastkari,
Volume 6, Issue 2 (9-2013)
Abstract
Background and objectives: Bisphenol A (BPA) is an endocrine disrupting chemical that releases to the environment through effluents of its producing factory, pulp and paper mill factories, and plastics industry. The purpose of this study was to investigate adsorption isotherms of removing BPA from aqueous solutions using single walled carbon nanotubes (SWCNTs).
Materials and methods: This study was an empirical investigation. Our experiments were conducted discontinuously using 50 mL of sample in each test. The variables of this study were the contact time (5, 15, 30, 60, 90, 120 min), the initial concentration of BPA (2, 5 , 20, 50 mg/L), and pH (3, 5, 6, 9, 11). The concentrations of BPA were measured using UV-Vis spectrophotometer.
Results: The maximum adsorption capacity was found to be 71.42 mg/g. The results of our experiments showed that maximum adsorption capacity at equilibrium was achieved at t = 60 min and pH = 9. Moreover, increasing the initial concentration is associated with an increase in adsorption capacity until it becomes constant.
Conclusion: The BPA adsorption on SWCNT follows Freundlich-Langmuir isotherm.
Mehdi Bahrami, Saeeid Brumand-Nasab, Heydar-Ali Kashkooli, Ahmad Farrokhian Firouzi, Ali-Akbar Babaei,
Volume 6, Issue 2 (9-2013)
Abstract
Background and Objectives: Among the heavy metals cadmium is of considerable environmental and health significance because of its increasing mobilization and human toxicity. The objectives of this research were to synthesize SDS modified magnetite nanoparticles (Fe3O4) and to determine its efficiency in cadmium removal from aqueous solutions.
Materials and Methods: Modified magnetite nanoparticles were synthesized and the effects of pH and contact time on cadmium removal efficiency were investigated in batch system. Then kinetics and isotherm models coefficients were determined in the optimum pH and equilibrium time conditions. Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infra red (FTIR) were used to characterize the modified magnetite nanoparticles synthesized.
Results: The SEM results showed that the diameter of the particles is 40-60 nm. It was found that the optimum pH value for maximum adsorption of 10 mg/L cadmium by 0.1 g adsorbent in 12 hr was 6. Kinetic study showed that the equilibrium time was 30 min. The adsorption kinetics fitted well using the Ho pseudo second-order kinetic model however, the adsorption isotherm could be described by the Freundlich model. The maximum adsorption capacity of modified magnetite nanoparticles for Cd2+ was found to be 9.604 mg/g.
Conclusion: The results of this study indicated that the modified magnetite nanoparticles can be employed as an efficient adsorbent for the removal of cadmium from contaminated water sources
Mohammad Ali Baghapour, Babak Jahed, Gholam Hossein Joshani,
Volume 6, Issue 3 (12-2013)
Abstract
Background and Objectives: Increasing waste tiers production has made the recycling of this solid waste a critical issue in the world. On the other hand, it seems contamination of groundwater to the petroleum pollutant like gasoline is a great threat to the health of societies in developing countries. The main objective of this study was gasoline removal from aquatic environment by waste tire derived activated carbon.
Materials and Methods: In this study for preparation of activated carbon from waste tires, KOH was used for chemical activation process. We used argon gas to prevent precursor oxidation . We applied N2 gas and BET isotherm for characterization of the prepared activated carbon texture. Isothermal and kinetic models were used for defining gasoline adsorption characteristic to adsorbent, and thermodynamic studies were used to determine the effect of temperature.
Results: Characterization results revealed that SBET and VTOTAL were 111.702m2/g and 0.124cc/g respectively. Langmuir and pseudo-second order models were the best isotherm and kinetic models for prediction of the adsorbent behaviors to adsorb gasoline. The Gibbs free energy changes were negative at all temperatures applied.
Conclusion: Produced activated carbon has desired surface area and adsorptive capacity for gasoline adsorption in aquatic environments and it seems preparation activated carbon from waste tiers is cheap, effective and environment friendly.
Mohammad Malakootian, Laleh Ranandeh Kalankesh,
Volume 6, Issue 4 (3-2014)
Abstract
Background and Objective: Humic substances in drinking water react with chlorine and form carcinogenic compounds. Humic acid is a principal component of humic substances and its separation from surface waters is crucial. Adsorption process is among different methods for separation of humic acid from surface waters and because of its simple and economical nature it has attracted considerable attention. The aim of this research was to examine performance of silicon nanoparticles in adsorption of humic acid in water. Materials and Methods: Experimental study was conducted on both synthetic and real water samples collected from Zarrineh Rood River, Tabriz before its entrance to water treatment process. We used instantaneous sampling method.The chemical quality of crude sample and its humic acid was determined and then the influence of pH, absorbent amount, and time on the removal of humic acid was evaluated. Therefore, the optimal conditions for each of these parameters were determined. In order to get better insight into the process of adsorption, the adsorption kinetic and equilibrium isotherm were studied. We measured humic acid concentration and TOC using spectrophotometer (Shimadzu /UV-1800, Japan) at a wavelength of 254 nm and TOC analyzer (Shimadzu model TOC-VCSH) measured. SPSS software and regression were used for data analysis. Results: At pH=4, retention time of 10 minutes, adsorbent amount of 0.25 g/L, we found that the highest percentage of humic acid adsorption was 88.4 and 81.8 for synthetic and real solutions respectively. The finding revealed that the removal of humic acid follows Freundlich isotherm ( =0.8172) and the second order kinetic model ( =0.9936). Conclusion: Removal in both real and synthetic solutions was less due to the reaction of influencing factors. However, considering the high percentage of humic acid removal under optimal conditions and its comparison with other methods, the removal of humic acid using SiO2 can be considered as an efficient method.
Mohamad Hadi Dehghani , Mamood Alimohammadi , Amir Hossein Mahvi, Noushin Rastkari, Masoome Mostofi, Maryam Gholami ,
Volume 6, Issue 4 (3-2014)
Abstract
Background and Objective: Various industries such as petrochemical, oil refinery, pharmaceutical, plastics, paper, steel and, resin produce a substantial of phenol and its derivatives. Wastewaters containing phenol need careful treatment before discharging into the environment due to their poor biodegradability and high toxicity. The objective of this study was to remove phenol by multiwall carbon nanotubes from aqueous solution. Materials and Methods: Adsorption process was implemented in a laboratory-scale batch with emphasis on the effect of various parameters such as contact time (5 to 120 minutes), pH (3- 11), initial concentration of phenol (5 - 50 mg/l) and the sulfate and chloride ions (20 - 200 mg/l) on adsorption process. To achieve a better realization of adsorption process, sorption kinetics and equilibrium isotherms were also determined. Results: The results indicated that maximum adsorption capacity occurred at concentration 50 mg/L and t =30 minutes. The uptake fluctuated very little in the pH range of 3–9, and at greater than 9 the absorption decreased suddenly. Moreover, the presence of sulfate and chloride ions had no effect on the process. It was found that adsorption kinetics and equilibrium data follow a pseudo-second-order kinetics model and a Freundlich isotherm model respectively. Conclusion: It is concluded that carbon nanotubes being effective in a wide range of pH, short time to reach equilibrium and the absence of competing ions on the absorption process can be used effectively in removing phenol from aqueous solution.
B Kakavandi, R Rezaei Kalantary, A Jonidi Jafari, A Esrafily, A Gholizadeh, A Azari,
Volume 7, Issue 1 (7-2014)
Abstract
Background and Objective: Extreme use of antibiotics and discharging them to the environment lead to serious consequences. Activated carbon is the most commonly adsorbent for these contaminants but its main drawback is difficulty of its separation. The objective of this study was synthesis of magnetic activated carbon by Fe3O4 and investigating its efficiency in adsorption of amoxicillin from synthetic wastewater. Materials and Methods: Materials and Methods: Physical and structural characteristics of the adsorbent synthesized were analyzed using SEM, TEM, XRD and BET techniques. The effect of factors like pH, initial concentration of amoxicillin and adsorbent, contact time, and temperature were investigated to determine thermodynamic parameters, equilibrium isotherms, and kinetics of adsorption process. Results: Physical characteristics of the magnetized activated carbon showed that Fe3O4 nanoparticles had the average size of 30-80 nm and BET surface area was 571 m2/g. The optimum conditions of adsorption were: pH=5, contact time=90min, adsorbent dose of 1g/L and temperature 200C. The equilibrium isotherms data showed that the adsorption process fitted both Freundlich and Longmuir models with the maximum capacity of 136.98 mg/g. The kinetic of the adsorption process followed pseudo second-order model. The negative values of &DeltaH0 and &DeltaG0 obtained from studying the adsorption thermodynamic suggested that amoxicillin adsorption on magnetic activated carbon was exothermic and spontaneous. Conclusion: The present study showed that the magnetic activated carbon has high potential for adsorption of amoxicillin, in addition to features like simple and rapid separation. Therefore, it can be used for adsorption and separation of such pollutants from aqueous solutions.
H Zarei, A.h Mahvi, S Nasseri, R Nabizadeh Noudehi, F Shemirani,
Volume 8, Issue 3 (12-2015)
Abstract
Objective and Background: Fluoride is an element widely found in the earth crust. Advantages and disadvantages of fluoride in the human body are depended on its concentration. Long-term consumption of drinking water contaminated with arsenic can cause adverse health effects such as skin lesions and cancer in humans. The aim of this study was to study efficiency of nano alumina on multi walled carbon nano tube for removal As(V) and fluoride from aqueous solution.
Materials and Method: In this study, nano-scale crystalline alumina was synthesized on single walled carbon nanotube by sol-gel method for using as a sorbent for solid phase extraction of Fluorine ion and arsenic(V). Response surface methodology based on Box-Behnken was used to assess the effect of independent variables on the response function and prediction of the best response value. In this study, effect of different parameters, such as contact time (10 to 120 min), pH (3-9), adsorbent dosage (0.25-1.5 g/L) and initial concentration of fluoride (2-8 mg/L) on efficiency of process was investigated. The structure of nano-scale alumina on multi walled carbon nano tube was determined by XRD and SEM techniques. Moreover, Freundlich and Langmuir isotherm models were used to calculate equilibrium constant.
Results: It was found that by increasing contact time and adsorbent dosage the rate of fluoride removal increased. However, by increasing pH and initial concentration the efficiency of fluoride removal decreased. High value for R2 (0.94) shows that removal of arsenic(V) can be described by this model. The Freundlich isotherm was the best fitted graph for experimental data with R2 more than 0.997.
Conclusion: In this study, it was observed that efficiency of arsenic(V) and fluoride removal was greatly increased by using nano-scale alumina on multi walled carbon nanotubes (MWCNTs).
A Shahbazi,
Volume 8, Issue 3 (12-2015)
Abstract
Background and Objectives: Rapid growing of Triton X-100 application in industries results in its appearance in effluents and threaten the aqueous ecosystems. Triton X-100 is not biodegradable and can accumulate in food chain.
Materials and Methods: In this study, sorption capacity of six synthesized zeolites with different regular porous structure was studied for triton X-100 (TX-100) surfactant and the results were compared with Clinoptilolite natural zeolite of Damavand region.
Results: Within all zeolite studied, Beta(200) showed the highest sorption capacity (about 575 mg/g), which is due to its regular pore structure with large pore diameter, channel intersections, high SiO2/Al2O3 ratio and high surface area. Langmuir monolayer isotherm and pseudo-second-order kinetic equation could provide well-fitted to the experimental data in simulating adsorption behavior of TX-100 over Beta(200) zeolite.
Conclusion: The adsorption feature was internal sorption and the intraparticle diffusion might be a rate-limiting control for Beta(200) zeolite. Results of experiments demonstrated that the hydrophobic zeolites with large pore diameter such as Beta(200) could be effective sorbents for industrial wastewater treatment features.
F Mohammadi, S Rahimi, Z Yavari,
Volume 8, Issue 4 (3-2016)
Abstract
Background and Objectives: In this work, biosorption of hexavalent chromium from aqueous solution with excess municipal sludge was studied. Moreover, the performance of neural networks to predict the biosorption rate was investigated.
Materials and Methods: The effect of operational parameters including initial metal concentration, initial pH, agitation speed, adsorbent dosage, and agitation time on the biosorption of chromium was assessed in a batch system. A part of the experimental results was modeled using Feed-Forward Back propagation Neural Network (FFBP-ANN). Another part of the test results was simulated to assess the model accuracy. Transfer function in the hidden layers and output layers and the number of neurons in the hidden layers were optimized.
Results: The maximum removal of chromium obtained from batch studies was more than 96% in 90 mg/L initial concentration, pH 2, agitation speed 200 rpm and adsorbent dosage 4 g/L. Maximum biosorption capacity was 41.69 mg/g. Biosorption data of Cr(VI) are described well by Freundlich isotherm model and adsorption kinetic followed pseudo-second order model. Tangent sigmoid function determined was the most appropriate transfer function in the hidden and output layer. The optimal number of neurons in hidden layers was 13. Predictions of model showed excellent correlation (R=0.984) with the target vector. Simulations performed by the developed neural network model showed good agreement with experimental results.
Conclusion: Overall, it can be concluded that excess municipal sludge performs well for the removal of Cr ions from aqueous solution as a biological and low cost biosorbent. FFBP-ANN is an appropriate technique for modeling, estimating, and prediction of biosorption process If the Levenberg-Marquardt training function, tangent sigmoid transfer function in the hidden and output layers and the number of neurons is between 1.6 to 1.8 times the input data, proper predication results could be achieved.
S Sobhanardakani, R Zandipak,
Volume 9, Issue 2 (9-2016)
Abstract
Background and Objective: Dyes are important pollutants that lead to producing serious hazards to human, other animals and organisms. Dyes are not biodegradable by aerobic treatment processes. Therefore, their removal from industrial effluents before discharging into the environment requires extreme and great attention. The aim of this research was to evaluate removal efficacy of methyl orange dye from aqueous solutions using NiFe2O4 nanoparticles.
Materials and Methods: This study was an empirical investigation in which NiFe2O4 nanoparticles were synthesized by co-precipitation method and were used as an adsorbent for the removal of methyl orange from aqueous solution. NiFe2O4 nanoparticles were characterized using X-Ray Diffraction (XRD), Transmission Electronic Microscopy (TEM), pHpzc and SEM-EDX elemental analysis methods. Experiments were conducted discontinuously using 20 mL methyl orange solution of 40 mg/L. The effect of variables such as pH (2-8), amount of adsorbent (0.009-0.07 g) and contact time (2-70 min) on the efficacy of dye removal was studied. Finally, experimental data were compared by Langmuir, Freundlich, and Temkin isotherms and pseudo-first-order and pseudo-second-order kinetic models.
Results: TEM images showed that the NiFe2O4 nanoparticles had spherical shapes with the size of 12 nm. The results indicated that removal efficiency increased up to 0.04 g adsorbent and 20 min contact time. The optimum pH for methyl range removal was 2. Moreover, under these conditions, the adsorption process followed the Langmuir adsorption isotherm with a correlation coefficient of 0.995 and pseudo-second-order kinetic model with a correlation coefficient of 0.999. Also, the maximum adsorption capacity of the prepared adsorbent was 135 (mg/g) for Langmuir isotherm.
Conclusion: The NiFe2O4 nanoparticles are effective and available adsorbents for the removal of methyl orange from industrial wastewater.
