Abdolrahim Davari, Farnaz Farahat, Haleh Davoudi,
Volume 36, Issue 0 (5-2023)
Abstract
Background and Aims: Insufficient adhesion between fiber post and root canal is the main reason for the failure of the restoration and the fiber post surface treatment can imprive the bond strength. Additionally, there is disagreement about the ideal method of preparation to achieve the desired bond. The aim of this study was to compare the effect of two surface treatment methods on push-out bond strength of fiber posts to root canals.
Materials and Methods: In this study, 45 healthy incisor teeth underwent root canal treatment. After preparing the post space, they were divided into 3 groups of 15, based on the surface treatment methods of the fiber post. In the first group as control group, no surface treatment was done on the fiber post. In the second and third groups, sandblasting with Cojet sand particles and 810 nm diode laser were used for surface treatment, respectively. Then, fiber posts were placed in all root channels by a self-adhesive resin cement. Then, the roots were cut in such a way that from each, 3 pieces with a thickness of 1.5 mm were obtained. Finally, the push-out bond strengths were measured using a universal testing machine. Data were analyzed by ANOVA using SPSS software. The level of significance was considered at P<0.05.
Results: The average bond strengths in three groups were as follows: control group, 2.877 ±1.430, sandblast group 6.318±3.444, and laser 4.224 ±1.890 MPa ± SD. The difference in the bond strength between the sandblast group and the control group was significant (P=0.001). However, the average of the bond strength of laser group was not significantly different from the control group. (P=0.03).
Conclusion: The findings of this study showed that unlike diode laser radiation, the use of Cojet sand particles for sandblasting the fiber post surfaces significanlty improved the bond strength.
Elahe Soltanmohamadi Borujeni, Ali Bavi, Mohammad Aghaali, Ali Saleh, Aida Mehdipour,
Volume 37, Issue 0 (3-2024)
Abstract
Background and Aims: Strong bond between the ceramic brackets and ceramic veneers has an important role in cosmetic treatment. The purpose of this study was to investigate the effect of aging on the shear bond strength (SBS) of ceramic brackets bonded to zirconia after surface preparation by Neodymium-doped Yttrium Aluminum Garnet (Nd: YAG) laser or sandblasting with alumina.
Materials and Methods: This experimental study was conducted on 24 zirconia blocks and these blocks were randomly divided into two groups for surface preparation and each was sub-divided into three time intervals. Surface preparation was done by sandblasting with alumina: in SG1 (Immediately after sandblasting), SG2 (2 weeks after sandblasting), and SG3 (3 months after sandblasting) groups. For the Nd: YAG laser (1/5W, 20Hz, 10s) with non-contact mode: in LG4 (Immediately after laser), LG5 (2 weeks after laser), and LG6 (3 months after laser) groups. The ceramic brackets were bonded to the zirconia blocks. The SBS and adhesive remnant index (ARI) were evaluated and compared among test groups. Dara were analyzed using Mann Whitney test.
Results: There was no significant difference between the SBS of SG1 and LG4 (P=0.430), SG2 and LG5 (P=0.382) and SG3 and LG6 (P=0.326) groups. LG4 group showed the highest shear bond strength. After aging (2 weeks and 3 months), the laser groups showed higher SBS. There was no significant difference in the ARI between SG1 and LG4 (P=0.220), SG2 and LG5 (P=0.154), SG3 and LG6 (P=0.527) groups.
Conclusion: No significant difference was observed between the Nd: YAG laser and sandblasted groups in terms of SBS and ARI over time. Therefore, Nd: YAG laser could be used as a surface treamnet method in Zirconia crowns for bonding to ceramic brackets.
