Journal of Dental Medicine

---

Dentine bonding systems are usually unfilled, and so their shrinkage may be significant. High shrinkage may cause internal stress at the interface between resin-composite restoration and the dentine substrate. Failure of the adhesive interface may be observed due to the interna! stress. The aims of this study were:A) To obtain a suitable method for measuring the kinetics of polymerisation shrinkage in unfilled resm at different thicknesses, particularly for thin films.B) Consideraing the effect of thickness on shrinkage.Scotchbond Multipurpose (3M) adhesive bond resin was used. To overcome the particular challenges presented by thin films, a filled-ring measurement procedure was used. Also, a non-contact laser analogue displacement sensor system was developed and applied to measure polymerisation shrinkage. Regression analysis was performed on a complete data set. Non-linear regression analysis established a logarithmic relationship between polymerisation shrinkage and layer thickness. The method applied in this study was found to be sensitive and accurate procedure for determining photo-polymerisation shrinkage of thin films. Polymerisation shrinkage increased with logarithmic of the adhesive thickness.

---

Dentin bonding agents create stronger bonding between dental composites and dentin. But, none of them can prevent the microleakage. The important factors of progressing microleakage are the stress of polymerization shrinkage of resin composite and removal of smear layer in total-etch technique. The aim of this study was the evaluation of the effect of experimental method (modifying smear layer and etching of enamel margin) and comparison with the total-etch technique. In this experimental method, 60 extracted human molar teeth were disinfected. Then, class 5 cavities were prepared on the buccal surface and 1 mm above CEJ. The specimens were divided randomly to 6 groups with iO samples in each group. The specimens groups were:
1- Scotchbond Muiti- Purpose Plus Adhesive System (S.B.M.P.P) +Tetric composite
2- S.B.M.P.P + Ariston composite
3- Ariston liner + Ariston composite
4- S.B.M.P.P without enamel and dentin etching + Tetric composite + rebonding with Flowable Tetric
5- S.B.M.P.P without enamel and dentin etching + Ariston composite + rebonding with Flowable Tetric
6- S.B.M.P.P without enamel and dentin etching + Tetric composite
After finishing and polishing, the specimens were termocycled, stained with fushin, sectioned within the specimens and evaluated for dye penetration with stereomicroscope. Wilcoxon Sign and Kruskal Wallis tests were used for statistical analysis.
Results showed that group 3 had microleakage more than groups of 1, 2 and 5 (P<0.0 5) and this difference was significant. There was no significant difference among the other groups.

---

Statement of Problem: Porcelain restorations are susceptible to fracture and a common method for repairing is the use of silane and composite on etched porcelain. Although HF is very effective in porcelain etching but has detrimental effects on tissues.

Purpose: In this study, the effect of APF and PHA was compared with HF in porcelain etching. Also the role of silane, unfilled resin and dentin bonding in bond strength of composite- porcelain was evaluated.

Methods and Materials: In this experimental in-vitro study, one-hundred twenty porcelain square blocks (552 mm) were prepared and bonding surfaces of each sandblasted. Samples were divided into three groups. The first group (n=40) were etched with buffered HF 9.5% (Ultradent) for 1 min., the second group (n=40) were etched with Iranian APF 1.23% (Kimia) for 10 minutes and the third group (n=40) were etched with Iranian PHA 37% (Kimia) for 1 min. Ultradent silane was applied on the surfaces of half of cases in each group. On the surfaces of half of silane-treated samples unfilled resin was applied and dentin bonding was used on the surfaces of the remaining. Samples without silane were treated in a similar manner. Composite cylinder with 4mm diameter and 2 mm height was bonded to porcelain. Specimens were stored in 37°C distilled water for 24 hours and subjected to 500 cycles. Shear bond strength was measured with an Instron machine and type of fracture was evaluated using a stereomicroscope. Results were analyzed using 3 way ANOVA, Kaplan- Maier and Tukey HSD tests.

Results: Findings showed that PHA and APF roughened the porcelain surface without creating retentive micro undercuts but HF etches porcelain and creates retentive microundercuts. Ultradent silane had no significant effect on bond strength of porcelain- composite. Unfilled resin with Ultradent silane compared with dentin bonding with the same silane is more effective in bond strength of composite- porcelain.

Conclusion: Based on present study, application of Ultradent silane on sandblasted and etched porcelain with PHA or APF cannot be used as an alternative to this silane on sandblasted and etched porcelain with HF.

---

Background and Aim: An important requirement for a dentin bonding agent is biological compatibility. Since dentin bonding agents are placed in cavity preparations with subgingival extensions, with direct contact to gingival and mucosal tissues, tissue response to these materials must be investigated. The aim of this study was to examine the cytotoxicity of AdheSE, a self etching adhesive, on human gingival fibroblasts.
Materials and Methods: In this experimental in vitro study, primary human gingival fibroblasts were exposed to different dilutions of primer & bond of AdheSE (Vivadent, Liechtenstein). The toxicity of the primer was tested in 30 seconds, 300 seconds and 24 hours. The cytotoxicity of the bond was analyzed in uncured mode after 20 seconds, 5 minutes and 24 hours. In cured mode, tested materials were analyzed after 24 and 48 hours. Cytotoxic effects were evaluated using MTT, cell counting and DNA condensation assays. Data were analyzed by two way repeated measure ANOVA with p<0.05 as the level of significance.
Results: MTT Assay revealed that uncured AdheSE Bond was toxic only in 10-1 dilution and the difference with control group was significant (P<0.05). By increasing the time to 300sec. and 24h, dilutions of 10-2 and 10-4 were the most cytotoxic respectively. Cytotoxicity of uncured primer after 30 sec. and 300 sec. began from 10-2 and after 24h began from 10-2 and reached to 10-1. AdheSE in cured mode showed significant difference with control group in 1:2 (P<0.001),1:4 & 1:6 (P<0.01) dilutions. In cell counting assay only the 1:2 dilution was significantly more toxic than control group. Apoptosis (a morphological and biochemical distinct form of cell death that regulates cell turnover) comprised in less than 5% of total death in both cured and uncured adhesives.
Conclusions: Based on the results of this study, by increasing the exposure time, smaller amounts of bonding could be cytotoxic. Cytotoxicity was related to material, dilution, time of exposure and curing. It would be necessary to identify the toxic ingredients of this adhesive and replace them by more biocompatible components.

---

Background and Aim: Fractured anterior teeth can be restored by adhesive bonding of the separated fragment to the remaining tooth structure. This invitro study evaluated the force required for fracture of rebonded fragments which were dried and rewetted for various time intervals prior to bonding.

Materials and Methods: One hundred and eight human mandibular incisors were selected and were divided into 9 groups and then were fractured. The fragments were stored in air at room temperature and ambient humidity. They were air dried for 30 minutes in group 1, 2 and 3,  6 h in group 4 and 5,  24 h in group 6 and 7, and 3 days in groups 8 and 9. The apical parts of the fractured teeth were stored in water.After storage in air, each fragment in group 1 was bonded to the remaining apical tooth structure with a bonding agent and flowable composite.In groups 2, 4, 6 and 8 after air drying the fragments were stored in water for 30min. The time of storage in water in groups 3, 5, 7, 9 was 24 hours. Then each fragment was bonded to the apical part structure. The mean force required for fracture was measured by a mechanical testing machine. One way ANOVA and Tuckey tests were used for analysis.

Results: There were statistically significant differences between different groups (p<0.001).The highest and lowest force required for fracture belonged to groups 3 and 8 respectively. The force required for fracture in group 1 was lower than group 2, 3, 5 and 7 and 9 and more than groups 4,6 and 8 with significant differences.While there were no significant differences among groups 3, 5, 7, 9 and 4, 6, 8 the force required for fracture in groups 2, 3, 5, 7 and 9 was more than 4, 6, 8 with significant differences.

Conclusion: This research revealed that the force required for fracture was affected by air storage of fragments prior to bonding. Also showed that with an increase in duration of drying the force required for fracture decreased and after a period of time it becomes steady. This study showed that in order to increase the fracture strength after air drying the fragment should be immersed in water for at least 24 hours prior to bonding.

---

Background and Aim: Since the clinical studies conducted to explore the effect of bonding agents on the success of fissure sealant are limited in number, the present study was conducted to compare the effects of two bonding agents on the success of fissure sealant of the saliva- contaminated teeth.

Materials and Methods: In this study, 63 teeth of 35 students aged 6-8 with healthy and newly-erupted upper jaw molar teeth, were selected and divided into two groups. In one group, single-bond and In the other, SE bond were used. As the teeth were newly erupted and the distopalatal area being in contact with the gingival sulcus and this fact that, this area was impossible to isolate, the distal sulcus of the contaminated teeth and the mesial area capable of adequate isolation were assumed isolated. For each group, after etching, the teeth on one side were treated with a sealant and the teeth on the other side were first bonded and then treated with the sealant. Hence, four groups were formed: bonded/isolated, bonded/contaminated, controlled/isolated and controlled/contaminated for any bonding agent. The results of the treatment were assessed in terms of the success and failure and then analyzed using Mc Nemar, and Chi-square tests and Cochran.

Results: The results of the study indicated that:1. Saliva contamination caused a significant increase in sealant failures(p<0.05).2. Use of the two bonding agents significantly increased the success of the sealant(p<0.05).3. Use of the two bonding agents significantly increased the success of the fissure sealant on the saliva-contaminated teeth, even more than when the teeth had been isolated and with only fissure sealant(p<0.05). 4. For the contaminated enamel, the results of SE bond were better than those of the single bond (p<0.05). However, in isolated condition the results of using single bond were better (p<0.05).

Conclusion: The results of the study supported the use of these two bonding agents in the treatment of fissure sealants under both isolated and contaminated conditions. Further, more SE bond seemed to be less sensitive to saliva contamination.

---

Background and Aim: Evaluation of shear bond strength and microleakage of bonding agents is important as these properties play main roles in adhesion of composite to dental tissues. Microleakage results in bacterial penetration into dentin tubules and enamel surfaces and causes sensitivity and recurrent caries followed by destruction of composite filling. Insufficient shear bond strength results in early failure of filling in low masticatory forces. The main goal of this study was to compare the microleakage and shear bond strength of an experimental adhesive and Scotchbond multi-purpose (MP) adhesive system.
Materials and Methods: In this experimental study, sixty extracted caries free human molar teeth were randomly assigned into 4 groups of 15 each for shear bond strength. Variables were bonding agents, enamel and dentin. Twenty teeth assigned into 2 groups of 10 each were used for valuation of the microleakage. Microleakage and shear bond strength were performed according to ISO TR 11405. All data were analyzed with parametric and non-parametric tests according to their normality distribution. Also, Weibull distribution performed on data.
Results: Data obtained from both microleakage and shear bond strength tests showed no significant difference between the experimental bonding and Scotchbond MP bonding (P>0.05). Furthermore, there was no significant difference between the microleakage of occlusal and gingival parts of both bondings (P>0.05).
Conclusion: Experimental adhesive bonding showed acceptable results regarding microleakage and shear bond strength. It may be concluded that the experimental dentin bonding had a comparable performance quality with that of commercial system.

---

Background and Aims: In this in-vitro study, the effect of multiple adhesive coating on the microshear bond strength of composite to dentin and surface microhardness of dentin after treatment with four adhesives (One Step Plus, One Step, Single Bond, Single Bond 2) were evaluated.

Materials and Methods: One hundred intact human molars were cut to obtain disks of dentin having 2 mm thickness. For the microshear bond test, sixty disks were randomly divided into four groups. In each group one type of adhesive was used. In one half of a disk two layers and in another half six layers of adhesive were applied. Cylinders with 1mm height was filled with a composite and light cured. The cross-head speed was 0.5 mm/min. Vickers microhardness was tested on forty dentin disks which divided into four groups and prepared in the same manner used for microshear bond test. Data were analyzed by Two-way ANOVA and Tukey tests.

Results: The highest and lowest bond strength were recorded as 29.49 ± 5.74 MPa (One Step Plus 6 layers), and 21.23 ± 4.83 MPa (One Step Plus 2 layers), respectively. The results indicated that One Step Plus bond strength in 6 Layers was significantly higher than 2 layers. The highest and lowest dentin hardness values were
39.08 ± 8.34VHN (Single Bond 2 layers) and 28.53 ± 5.98 VHN (One Step Plus 6 layers). None of the adhesives exhibited significant difference in hardness with regards to the layers applied (P>0.05). Presence of filler in adhesives had no significant effect on bond strength (P=0.05) whereas caused significant decrease in the dentin microhardness (P<0.05). In addition, type of solvent had significant effect on the bond strength and bond strength was significantly higher in acetone-base adhesives (P<0.05). However, dentin microhardness was significantly higher in the ethanol-base adhesives (P<0.05).

Conclusion: Multiple adhesive coating had no influence on the microshear bond strength of composite to dentin and dentin surface microhardness. It was dependent on the type of adhesive used.

---

Background and Aims: The aim of this in vitro study was to assess the shear bond strength of amalgam to dentin using four dentin adhesive systems.
Materials and Methods: One hundred human molars were selected. After enamel removal, a dentin cylinder with 3 mm thickness was prepared. Eighty specimens were resorted with amalgam and four dentin adhesive systems as follows (n=20): group 1, Scotch Bond Multi-Purpose group 2, One Coat Bond group 3, PQ1 and group 4, Panavia-F. In group 5, 20 specimens were resorted with amalgam and varnish as control group. The specimens were incubated at 37°C for 24 h. The shear bond strengths were then measured by using push out method. The data were analyzed by one-way ANOVA and post hoc Duncan's tests.
Results: Mean values for bond strengths of test groups were as follows: group 1=21.03±8.9, group 2=23.47±9, group 3=13.16±8.8, group 4=20.07±8.9 and group 5=14.15±8.7 MPa±SD. One-way ANOVA showed the statistically significant difference between the bond strengths of five groups (P=0.001). Post hoc Duncan's test showed significant difference between groups 1and 3 (P=0.008), groups 1 and 5 (P=0.019), groups 2 and 5 (P=0.0008), groups 4 and 5 (P=0.042), and groups 3 and 4 (P=0.018).
Conclusion: Results of this study showed that the bond strength of amalgam to dentin using One Coat Bond as dentin adhesive system was higher than that observed in other dentin adhesive systems.

---

  Background and Aims : The aim of this study was to evaluate the effect of chlorhexidin 2%, sodium hypochlorite 2.5% and hydrogen peroxide 3% as three effective and regular disinfectants on the microleakage of 7th generation bonding agents in vitro.

  Materials and Methods: 45 extracted molar teeth without carries were collected and disinfected. On buccal and lingual aspects of these teeth conventional class V cavity preparation were done (90 cavities), then randomly divided to 4 groups, three of them had 10 teeth (20 cavities) and one of them had 5 teeth (10 cavities) as control group. Cavities in each experimental group prepared with one of the disinfectants and then 7th generation bonding (Optibond all in one, kerr) was used as noted by manufacturer, then cavities filled with composite and polished. Bonding agent was used without our previous disinfectants manipulation in control group. Specimens were thermocycled with 1000 thermal cycles between 5 and 55 ⁰ C each for 30 seconds and then immersed in the methylene blue 5%, then sectioned mesiodistally and investigated for microleakage under stereomicroscope (Olympus, Japan). Data were analyzed using Kruskal-Wallis and Wilcoxon mean rank tests.

  Results: Despite the lower mean rank values for the untreated group at both occlusal and gingival aspects, the Kruskal-Wallis procedure (α=0.05) showed that the treatment factor did not significantly affect the mean rank values neither in occlusal (P=0.12) nor in gingival (P=0.39) part of cavities.

  Conclusion: According to the results of this study, antimicrobial agents such as chlorhexidine 2%, sodium hypochloride 2.5% and hydrogen peroxide 3% can be used perior to 7th generation dentin bonding agent
(Optibond all in one, kerr) without much concern.

---

---