Showing 34 results for Jafari
Ameneh Fayazi, Mostafa Pouyakian, Mohammad Javad Jafari, Soheila Khodakarim,
Volume 9, Issue 1 (4-2019)
Abstract
Introduction: Changing the national System of Classification and Labelling of Chemicals to Globally Harmonized System of Classification and Labelling of Chemicals (GHS) is beneficial for all the industries of the countries, their workers and the general public. Increasing the awareness of chemical hazards, improving the safety uses, reducing chemical accidents, and providing better conditions for emergency response in the event of chemical accidents, are some of the most important benefits of the GHS. Present study aimed to develop a tool for assessing the awareness level of chemical related personnel using the GHS and current status.
Material and Methods: By reviewing the literatures, the GHS Guide, available sources and consultation with experts, two questionnaires were developed to assess the level of awareness of chemical related personnel and current statue. The two designed questionnaires included personal information, multiple choice questions and questions related to safety signs. The face and content validity was conducted using the experts’ panel assessment. The face validity, content validity ratio (CVR) and content validity index (CVI) were all calculated for each question.
Results: Content Validity Ratios (CVR) and Content Validity Index (CVI) were calculated for each question. The general clarity, general fit and general simplicity of the awareness questionnaire (questionnaire number 1) were obtained 0.87, 0.91 and 0.77, respectively. The mean content validity index and the mean content validity ratio were obtained 0.85, 0.85, respectively. The overall clarity, overall fit, and the general simplicity of the current status questionnaire (questionnaire number 2) was 0.92, 0.89 and 0.93, respectively. The mean content validity index and mean content validity ratio were obtained 0.92 and 0.81, respectively.
Conclusion: The two questionnaires used to assess the awareness level of chemical related personnel and current statue of GHS, were identified as valid instruments and therefore is recommended as a valid tool for future studies.
Roohollah Ghasemi, Farideh Golbabaei, Mohammad Javad Jafari, Mohammad Reza Pourmand, Sasan Rezaei, Ramin Nabizadeh, Ensieh Masoorian,
Volume 9, Issue 2 (6-2019)
Abstract
Introduction: Air pollution is now recognized as an important environmental and health concern. Biological control processes, due to their durable, cost-effective and eco-friendly, have become a good alternative to physic-chemical methods. Biotechnology is based on the activity of microorganisms.
The aim of this study was to compare the capability of Pseudomonas Putida PTCC 1694 (bacteria) and Polarotus Stratus IRAN 1781C (mushroom) in the removal of toluene from the air stream and its biodegradation under same operating conditions.
Material and Methods: To this purpose, a bio filter containing two parallel columns was designed and constructed on a laboratory scale and the experiments were carried out based on measuring the removal efficiency (RE), elimination capacity (EC) and pressure drop in these two columns. Thus, the bacteria were inoculated in one of the columns and in the other the fungus was inoculated.
Results: The bacterial testing lasted for 20 days and the fungal testing lasted for 16 days. The contaminant loading rates (LR) for bacterial and fungal bio filters were 11.65±2.26 and 11.94±2.56 g/m3.h, respectively. The results showed that the fungal bio filter was more capable of eliminating of toluene vapor than bacterial bio filter (9.65±3.53 vs 9.18±2.6 g/m3.h). However, the pressure drop in the bacterial bio filter was lower than the fungal bio filter (1±0.28 vs 1.1±0.32 cm water).
Conclusion: According to the results, fungal bio filtration appeared to be more successful than bacterial bio filtration in the removal of toluene.
Rezvan Ghashghaei, Gholam Reza Sabzghabaei, Soolmaz Dashti, Samira Jafari Azar, Farhad Salehipour,
Volume 9, Issue 2 (6-2019)
Abstract
Introduction: The accidents involving the transport of hazardous goods in ports have always been one of the human and environmental threats. The purpose of this research is to study the consequences of incidents involving dangerous goods by modeling and prediction of catastrophic consequences of these goods using the Software valid of management, so in addition to the affected area of the various outcomes of these goods, To provide the necessary management measures to reduce human and environmental toll on keeping dangerous goods in ports and warehouses to be paid.
Material and Methods: The study performed from PHAST and ALOHA software in the container terminal in the region of Bandar Imam Khomeini and, to verify the consequences of styrene of toxicity of dangerous goods, was used.
Results: According to the results of this study, the extent of pollution coverage (the forbidden region) at least a radius of 79 meters and the best place for placement the Support groups are a radius of 106 meters, around the area dangerous goods. Finally, to offer management practices to avoid or reduce the consequences of possible sites and warehouses storing goods in the study area was dangerous.
Conclusion: In this study, methanol reservoir was introduced as the main focus of risk; therefore, the implementation of safety rules, eliminating mechanical failures, personal protection and education, and effective measures to prevent and fight fire are proposed for decreasing the probable losses and fatalities are necessary. As well as measures such as drainage design and appropriate land cover of hazardous goods and predictions for emergency evacuation with regard to atmospheric conditions (speed and wind direction) were recommended.
Roohalah Hajizadeh, Ali Khavanin, Ahmad Jonidi Jafari, Mohammad Barmar, Somayeh Farhang Dehghan,
Volume 9, Issue 4 (12-2019)
Abstract
Introduction: Nowadays multiple techniques have been developed to noise control. One the most important way is the control based on sound absorption and insulation. The purpose of current study was to improve the acoustic properties of soft polyurethane foam regarding combined sound absorption and insulation characteristics.
Materials and Methods: Polyacrylonitrile and polyvinylidine fluoride nanofibers are fabricated using solution electrospinning technique. Nano-clay particles (montmorillonite, 1-2 nm in diameter) were purchased from Sigma-Aldrich, Inc. Experimental design was prepared using Design-Expert ver.7 software. The 50 samples of nanocomposites were fabricated on the basis of experimental run. The measurement of sound transmission loss and the absorption coefficient was conducted using BSWA SW477 550005 Impedance Tubes according to the standard ASTM E2611-09 and ISO10534-2, techniques. Response surface methodology (RSM) with central composite design (CCD) was applied to optimize the conditions to produce nanocomposites for each frequency range.
Results: The polymer nanocomposites had the higher combined sound transmission loss and the absorption coefficient than pure polyurethane foam. Their combined transmission loss and the absorption coefficient in the low, middle and high frequency range was 02.02, 1.91 and 2.53 times higher than the pure polymer. The combined transmission loss and the absorption coefficient in all frequency ranges have been increased by increasing the thickness of the composites and air gap. At a thickness of 2 cm, the combined composites, sound transmission loss and the absorption coefficient increased with the increase of content of both nanofibers. The highest combined transmission loss and the absorption coefficient was observed when mass fraction of nanofibers was in at its maximum level.
Conclusion: This study showed that the adding nano-clay particles, polyacrylonitrile and polyvinylidine fluoride nanofibers to polyurethane foam can lead to increased sound transmission loss and the absorption coefficient. The obtained optimized nanocomposite can be applied to noise control where requiring the absorption as well as reduction of sound transmission.
Hasan Iravani, Mohammad Javad Jafari, Rezvan Zendehdel, Soheila Khodakarim, Athena Rafieepour,
Volume 10, Issue 1 (3-2020)
Abstract
Introduction: Hydrogen sulfide (H2S) is a toxic gas that has adverse effects on human health and equipment. One of the methods for eliminating of H2S gas is the use of adsorbent substrate. In this study, the effect of adding iron oxides including ferric (Fe2O3) and magnetite (Fe3O4) nanoparticles to ZSM-5 zeolite substrate was investigated on the efficiency of H2S elimination from the air stream.
Methods: In this study, Fe2O3 and Fe3O4 nanoparticles were impregnated in ZSM-5 zeolite in two weight ratios of 3% and 5%. The structural properties of the substrate were studied using XRD, BET and SEM. Then, the efficiency of substrate in removing H2S from air was studied while H2S gas was injected in to a pilot setup, in concentrations of 30, 60, 90 and 120 ppm at three bed temperatures of 100, 200 and 300 o C.
Results: The accuracy of combination and the morphology of inoculated zeolite was confirmed using XRD and SEM. The BET test also showed that the loading of iron oxide nanoparticles on the substrate educed the substrate surface area. The results revealed that increasing the percentage of nanoparticles and increasing the temperature from 100 ° C to 300 ° C increase the time of breakthrough point. The maximum adsorption capacity was obtained equal to 44.449 (mgH2S/g zeolite) for ZSM-5/Fe3O4-5% substrate at 120 ppm concentration.
Conclusion: Iron oxide nanoparticles inoculated in ZSM-5 zeolite substrate increase the capability of eliminating of H2S gas at high temperatures and therefore can be used as a suitable method for the elimination of similar pollutants.
Fatemeh Fasih-Ramandi, Asghar Sadigzadeh, Mohammad-Javad Jafari, Soheila Khodakarim,
Volume 11, Issue 1 (3-2021)
Abstract
Introduction: Determining the size distribution of the particles for assessing their effects on human health and their control mechanisms is very effective. One of the most important equipment used in determining particle size distribution is the DMA. In this study, in addition to the design and construction of a DMA, the size distribution measurement of aerosol particles was carried out.
Material and Methods: In this experimental-laboratory study, according to the theoretical principles, the geometric dimensions and operating conditions of the DMA were determined by Fortran programs. The design of the technical drawing of the DMA was done using the Salidworks-2017 software. The DMA designing was performed by studying the size distribution of 12 ranges of DOP particles in 15 voltages.
Results: The results of applying different voltages to the DMA showed that one range of particles size had the highest number of particles in the output of the DMA at each voltage. As the number of particles with the size of 0.26-0.3 µm at 3500 volts and those larger than 2 µm at 9000 volts is the highest at the output of the DMA.
Conclusion: DMA systems are a robust tool in determining the particle size distribution. As by knowing the required voltage to separate a specific size of the particles, the DMA will be able to specify the spectrum of unknown particles.
Reza Jafari Nodoushan, Mostafa Azimzadeh, Sahar Bagheri, Arefeh Dehghani Tafti,
Volume 11, Issue 4 (12-2021)
Abstract
Introduction: In recent years tend to use of natural fibers has increased in making sound absorbers. Fiber-based natural materials have low density, low production costs, and are biodegradable.
Material and Methods: In this study, the effect of nanoclay and the behavior of the nanocomposite specimens containing tea waste, polypropylene, and nanoclay in the sound absorption coefficient are investigated.
Results: The results showed the sound absorption coefficient increases by increasing the tea waste weight percent of the polypropylene. 60% increase in tea waste has a special role in the absorption of sound waves at a frequency of 1000 Hz and 2500 to 6300 Hz frequency range as the TW60 N5 sample has the sound absorption coefficient 0.94 and 0.84 in 1000 and 6300 Hz frequencies, respectively. Comparison of the sound absorption coefficient of composite and nanocomposite showed that sound absorptions increase by adding nanoclay to the 5%, at frequencies above 2000 Hz.
Conclusion: Tea waste-based sound absorbers can be used in noise control due to the high acoustic absorption and no harmful effects on human health.
Ehsan Garosi, Adel Mazloumi, Amir Homayoun Jafari, Ahmadreza Keihani, Ali Sharifnezhad, Mansour Shamsipour, Ramin Kordi,
Volume 12, Issue 2 (6-2022)
Abstract
Introduction: The use of exoskeletons as a new ergonomics intervention to reduce musculoskeletal disorders risk factors and increase human performance has emerged in the fourth-generation industrial revolution. The aim of this study was to assess the cervical exoskeleton effect on the neck and shoulder muscles electrical activity.
Material and Methods: In this experimental study, 14 male participants were asked to perform the simulated overhead work with and without using the cervical exoskeleton at two neck postural angles randomly. During the task, electromyography of the target muscles in the neck and shoulders was recorded. In addition, at the end of each task, participants completed a perceived discomfort questionnaire. Electromyographic signals were processed with Matlab 2017b software and the level of the electrical activity of the target muscles was normalized to the maximum muscle activity. Data analysis was performed using Random intercept mix model in STATA 14 software.
Results: Mean perceived discomfort in the neck and shoulders regions significantly reduced by the exoskeleton device, but there was no statistically significant difference in other areas. Also, the mean activity level of sternocleidomastoid and splenius capitis muscles on the right and left was significantly decreased during the use of the cervical exoskeleton. However, this difference showed a significant increase in trapezius muscles.
Conclusion: The use of the neck exoskeleton was associated with a reduction of muscle electrical activity and the perceived discomfort in the neck area. These results may be related to transferring neck and head weight by the exoskeleton retaining jack during the neck extension to other areas of the body. The exoskeleton design did not provide support for the shoulder and arm area, which explains the reason for the non-significant results in the shoulder area. Using the exoskeleton with the additional support in shoulder area could be considered as an ergonomic intervention in such overhead works.
Masoud Feyzi, Ali Jafari, Hojat Ahmadi,
Volume 12, Issue 2 (6-2022)
Abstract
Introduction: Due to the non-developed mechanization situation, chainsaw is a widely used tool in Iranian forests. This tool can trigger unwelcome disorders (e.g., white finger syndrome) due to the transmitted vibrations from its handle to the body members. Characterizing these vibrations can result in minimizing the intensity of these disorders. This study aims to investigate the effect of different hardwood species (Beech, Hornbeam, and Alder) on the vibrations transmitted to the wrist and arm.
Material and Methods: Experiments are conducted during four operations including Beech-, Hornbeam-, and Alder-cross-cutting and without cutting as the control sample. Vibration accelerations in three directions of a local Cartesian coordinate system are measured at three points including chainsaw handle, operator's arm and wrist. Using the time and frequency spectra of vibration accelerations, root mean square (RMS), total vibration acceleration, total vibration transmissibility, and frequency-weighted vibration acceleration are calculated based on ISO 5349 (2001) and ISO 10819 (2013) standards. The calculated parameters were statistically analyzed in SAS.
Results: The results showed that variations in wood species could significantly affect the RMS at all three points. The RMS magnitude decreases from handle towards the arm. Interestingly, a significant variation in vibration transmissibility is observed in different frequencies. This study confirms that body organs can damp the high-frequency vibrations better than the low frequency ones.
Conclusion: Although the RMS for cutting operations is less than the control sample, frequency-weighted vibration acceleration and consequently the risk of white finger syndrome is higher in cutting regimes. Furthermore, some vibration accelerations (below 40 Hz for wrist and below 25 Hz for arm) are amplified during transmission despite significant damping in total vibrations.
Ali Jafari, Mohammad Reza Monazzam, Ali Khavanin, Maede Lashgari, Seyed Ali Ghoreyshi,
Volume 13, Issue 1 (3-2023)
Abstract
Introduction: Wood-Wool Cement Panels (WWCPs) are environmentally friendly sound absorbers also used as heat, energy, and moisture insulators. WWCPs have suitable mechanical properties due to using Portland cement and wood strands as raw materials. In this study, the acoustic performance of WWCP absorbents will be investigated.
Material and Methods: The mixed raw materials were molded under pressure through a hydraulic press to fabricate the WWCP samples. Samples were demolded after 24 hours. Samples were created with two thicknesses of 2 and 4 cm and three bulk densities of 400, 500, and 600 kg/m3 to examine the impact of thickness and bulk density on the acoustic absorption coefficient. The sound absorption coefficients were determined as a function of frequency for two frequency ranges: low (63-500 Hz) and high (630-6300 Hz).
Results: In the low-frequency range, increasing the thickness from 2 to 4 cm increased the absorption coefficient at 500 Hz by 0.16 and 0.23 for densities of 400 and 500 kg/m3, respectively. Increasing the thickness added an absorption peak and increased the value of these absorption peaks to 0.9 in the high-frequency range. When the bulk density of the 4-cm-thick samples increased from 400 to 600 kg/m3, the low-frequency absorption peak increased by 0.33. In the high-frequency range, the same density change increased the absorption peak by 0.26 for the 2-cm-thick sample.
Conclusion: Increasing the thickness of WWCP improves both its high- and low-frequency acoustic absorption coefficients. In addition, increasing the bulk density to approximately 500 kg/m3 boosts the sound absorption efficiency in both frequency ranges.
Adel Jafari, Farshid Ghorbani Shahna, Abdulrahman Bahrami, Majid Habibi Mohraz,
Volume 13, Issue 2 (6-2023)
Abstract
Introduction: With the spread of the COVID-19 pandemic and the lack of adequate protection by existing protective equipment, many researchers’ attention has turned to developing improved respiratory protection equipment. Considering their special properties and nanoscale dimensions, electrospun nanofibers are a suitable option for improving operational characteristics of substrates used in conventional facemasks. This study aimed to optimize the electrospinning process of polyacrylonitrile nanofibers (PAN) containing ZIF8 and use the optimized substrate in medical facemasks to increase their protective performance.
Material and Methods: This study employed an environmentally friendly method to synthesize ZIF8 in an aqueous environment. Then, PAN/ZIF8 polymer solutions were prepared in dimethylformamide. The effects of electrospinning parameters, including electrospinning voltage, polymer solution concentration, electrospinning distance, and polymer injection flow rate on diameter and uniformity of nanofibers were investigated. Electrospinning conditions were optimized using response surface methodology (RSM) and central composite design (CCD) to obtain desired values for response (dependent) variables. Finally, optimized PAN/ZIF8 and PAN nanofibers were electrospun on spun-bond substrate. Base weight, average diameter of fibers, filtration performance, pressure drop, and quality factor of fabricated substrates were assessed.
Results: According to results, optimal conditions for electrospinning of PAN/ZIF8 polymeric solution for polymer concentration (A), electrospinning voltage (B), electrospinning distance (C), and polymer injection flow rate (D) were respectively 70 w/v%, 20 kV, 18 cm, and 0.4 ml/h. Moreover, despite lower base weight of PAN/ZIF8 nanofiber mask, it displayed higher filtration performance (98.51%), lower pressure drop (31.42 Pa), and higher quality factor (0.140 Pa-1) in comparison to other studied masks.
Conclusion: Experimental models developed in this study provide acceptable values for filtration efficiency and quality factor for filtration applications. Additionally, they serve as a guideline for subsequent experiments to produce uniform and continuous nanofibers with desired diameter for future applications in absorbent media (intermediate absorbent layers) of respirators.
Marzieh Izadi Laybidi , Adel Mazloumi , Jebraeil Nasl Saraji, Faramarz Gharagozlou, Amir Homayoun Jafari, Zahra Shirzhiyan, Kamal Azam ,
Volume 13, Issue 3 (9-2023)
Abstract
Introduction: Air traffic control is a very complex process, including multiple human-machine interactions. Human mental workload plays an important role in this process. Nowadays, electroencephalography indexes are considered as new indicators in the field of assessment of mental workload. The purpose of the present study was to investigate the relationship between EEG theta power and mental workload in air traffic control simulation.
Material and Methods: Fourteen air traffic controllers participated in this study. Controllers carried out two scenarios, including low and high workload, based on task load factors in an air traffic control simulator. Mental workload was assessed in these two scenarios by the NASA-TLX questionnaire. EEG signals were continuously recorded during air traffic control tasks. Afterward, absolute theta power was extracted from participants’ EEG using Fast Fourier Transform (FFT) by the MATLAB software and was compared with each other in terms of high and low workload.
Results: The results showed a significant relationship in absolute theta power during low and high workload scenarios in all regions of the brain (p < 0.05). Absolute theta power increased primarily in the frontal region during the high workload scenario. Also, there was a significant increase in the relationship between work experience and absolute theta power at the F3 region during the high workload scenario (P=0.021, r=0.607).
Conclusion: Absolute theta power provides a good parameter to assess mental workload at different levels of air traffic control tasks. Therefore, it can be used as a tool for the design of human-machine complex systems.
Mahdi Alinia Ahandani, Saba Kalantary, Monireh Khadem, Fatemeh Jafari, Kamal Azam, Farideh Golbabaei,
Volume 13, Issue 4 (12-2023)
Abstract
Introduction: VOCs are harmful air pollutants that must be detected, monitored and eliminated. Adsorber tubes are standard tools for this task, specifically activated carbon tubes with high adsorption and selectivity. This research aims to compare the structural and functional characteristics of domestically produced activated carbon tubes with the conventional commercial ones for sampling toluene, a volatile organic compound.
Material and Methods: The characteristics of each adsorbent, such as structure, morphology, porosity, and element composition, were examined by SEM photography, BET testing, and EDAX analysis. The central composite design (CCD) method was employed to investigate the adsorption properties of the adsorbents. The input concentration and readsorption time of the samples were the variables considered in this study. Additionally, a field phase of personal air sampling was performed to evaluate the effectiveness of adsorbent tubes.
Results: SEM and BET analyses indicated that the porous structure of domestic activated carbon was comparable to the model produced by SKC. EDAX analysis detected a minor impurity (1%) in the domestic activated carbon adsorbent. The adsorption performance was significantly influenced by the variations in readsorption time and pollutant input concentration. The accuracy and precision of the performance of the domestic adsorbent tube were obtained as 90.77% and 91.76%. The field phase results demonstrated that the amount of pollutant adsorbed in the SKC-activated charcoal adsorber did not differ significantly during 0 to 30 days. However, the domestic adsorber showed a significant difference in the same period. The overall performance of the two adsorbers did not exhibit a significant difference between 0 and 30 days.
Conclusion: Despite minor structural differences, the adsorption efficiency of toluene by domestic adsorbent tubes in sampling high concentrations is very similar to its commercial type. However, it is not recommended for use in low-concentration environments (10 ppm and less).
Rohollah Fallah Madvari, Reyhaneh Sefidkar, Reza Raeisi, Gholamhossein Halvani, Reza Jafari Nodoushan,
Volume 14, Issue 2 (6-2024)
Abstract
Introduction: Considering the abundance and the large number of workers employed in micro and small industrial workshops in Iran and the importance of workers’ health, the present study aimed to investigate the mediating role of chronic fatigue in the relationship between mental workload and work ability with cognitive failure using path analysis.
Material and Methods: This study was conducted using a cross-sectional design on a sample of workers employed in micro and small industrial workshops in the city of Eghlid. Data were collected utilizing various measures, including demographic and occupational information questionnaires, the NASA Task Load Index (NASA-TLX), the Work Ability Index (WAI), and questionnaires for chronic fatigue and cognitive failure. The correlation test and path analysis modeling were used in SPSS (version 24) and AMOS softwares to investigate the relationship between variables.
Results: The mean scores of mental workload, work ability, chronic fatigue, and cognitive failure
were 69.63, 35.20, 15.58, and 53.30, respectively. The values of the goodness of fit indices lead to
the confirmation of the conceptual model by the research data. Also, based on the findings of the path analysis, the current research model has a good fit (CFI=1.00, GFI=0.998, NFI=0.999, AGFI=0.98 and RMSEA=0.003(0.00,0.169)).
Conclusion: The path analysis results indicate that chronic fatigue plays a significant mediating role
in the relationship between mental workload and work ability with cognitive failure. A better understanding of the mediating mechanisms and complex effects of these relationships can contribute to improving the management of chronic fatigue and enhancing cognitive performance in the workplace.
Ali Jafari, Mohammad Reza Monazzam Esmaeelpour, Fardin Zandsalimi,
Volume 14, Issue 2 (6-2024)
Abstract
Introduction: A wood-wool cement panel (WWCP) is wood wool combined with Portland cement mortar. This environmentally friendly acoustic material can be used as a thermal insulator and fire-resistance material with desired mechanical properties. This study aimed to determine the mechanism by which WWCP absorbs sound and the effect of production and application parameters on absorption
Material and Methods: The samples were prepared from poplar wood wool and white Portland cement as a binder in two Cement Fiber Ratios (CFR), namely 2:0.7 and 2:0.95, with bulk densities of 400, 500, and 600 Kg/m3 and thicknesses of 2 and 4 cm. Three layers of backing: air, polyurethane foam, and glass wool were examined separately. Acoustic absorption coefficient was measured using an impedance tube based on ISO 10534-2.
Results: The highest increase in the average absorption coefficient due to the increase in thickness was observed for the sample with a density of 400 kg/m3 and CFR = 2: 0.95, equal to 0.3. Increasing the bulk density to 500 kg/m3 for most samples and in the high-frequency range led to rising absorption efficiency. The optimal backing effect was due to the placement of 4 cm of polyurethane foam behind the sample, which in both thicknesses led to an absorption peak with an absorption coefficient higher than 0.95 at frequencies between 400 and 500 Hz. Selected samples showed that painting WWCPs led to a limited drop in absorption coefficients at high frequencies, comparing the before and after painting results with oil-based paints.
Conclusion: Tuning the absorption frequencies of these absorbers can be achieved by altering factors such as the thickness or density. It has been demonstrated that the effects of thickness and bulk density on the sound absorption of WWCP are related to each other. Concerning the CFR values, increasing the density did not significantly affect absorption in the two frequency ranges.
Akram Tabrizi, Mostafa Jafarizaveh, Hamid Shirkhanloo, Farideh Golbabaeie,
Volume 14, Issue 4 (12-2024)
Abstract
Introduction: Volatile organic compounds (VOCs) are hazardous toxic pollutants in the air, which are released from various industrial sources. Due to the adverse effects of xylene on health, the effective removal of VOCs from the air by nano sorbents is crucial. In this study, nanographene (NG) and nanographene oxide (NGO) were used as adsorbents to investigate the efficiency of xylene removal.
Material and Methods: In this study, in order to investigate the absorption efficiency of nanographene and nanographene oxide after the synthesis of nano absorbents in a dynamic system, xylene vapor was produced in a chamber in pure air and stored in a Tedlar sampling bag and then transferred to the adsorbent. Subsequently, the effect of various parameters such as xylene concentration, inlet air flow rate, and absorbent mass values at 32% humidity and 25°C temperature on the absorption rate and performance of the desired absorbents was investigated. Finally, the gas chromatographic flame ion detector (GC-FID) determined the concentration of xylene in air after the adsorption-desorption process.
Results: The average adsorption efficiencies for NG and NGO were found to be 96.8% and 17.5%, respectively. The characteristics of the NG and NGO adsorbents indicated that the particle size range was less than 100 nanometers.
Conclusion: The results demonstrated that the adsorption efficiency of NG for the removal of xylene from the air is higher than that of NGO. The GC-MS method validated the proposed approach in real air samples.
Soqrat Omari Shekaftik, Jamal Biganeh, Maedeh Hosseinzadeh, Hamidreza Jafari Nodoushan, Neda Mehrparvar,
Volume 14, Issue 4 (12-2024)
Abstract
Introduction: Workplaces often contain potential risks, such as exposure to toxic chemicals. Conducting a thorough health risk assessment helps employers recognize these dangers and implement necessary controls. In the 20th century, modern risk assessment frameworks began to be established with the rise of public health agencies.
Material and Methods: The present study is a narrative review. In order to obtain necessary information, Persian and English texts were searched in Web of Science, PubMed, Scopus, SID and Magiran databases. Keywords such as “health risk assessment”, “chemicals” and “nanomaterials” were used in this study.
Results: Both quantitative and qualitative health risk assessments play critical roles in occupational health, with each method providing different levels of depth and accuracy depending on the situation. EPA Model, Monte-Carlo Simulation, Physiologically Based Pharmacokinetic (PBPK) Modeling, Quantitative Structure-Activity Relationship (QSAR) Models, Probabilistic Risk Assessment (PRA), Life Cycle Impact Assessment (LCIA), and Biologically Based Dose-Response (BBDR) Models, are among the most important quantitative methods for assessing the health risk of chemicals. COSHH Model, ICCT Model, ICMM Model, Australian Model, and Romanian Model, are the most important qualitative methods for health risk assessment of chemicals. In addition to the quantitative and qualitative methods, semi-quantitative methods like Singapore Model, LEC Method, and SEP Model, have also been proposed for assessing the health risk of chemicals. The preference for qualitative over quantitative methods in the risk assessment of activities involving nanomaterials stems from substantial uncertainties, limited data availability, and the unique and complex behaviors of nanomaterials in the workplaces.
Conclusion: Overall, the evolution of health risk assessment methods reflects a continuous drive towards greater accuracy, reliability, and relevance. As we continue to innovate and expand our knowledge, the field is well-positioned to address the complex and evolving landscape of chemical and material risks, ensuring the protection of human health and the environment.
Mahdi Jafari Nodoushan, Amir Houshang Mehrparvar, Mohammad Ali Ghoveh Nodoushan, Reza Jafari Nodoushan, Ali Karimi,
Volume 15, Issue 2 (7-2025)
Abstract
Introduction: Safety in healthcare facilities is critically important for the health and well-being of employees, patients, and organizational effectiveness. In recent years, various studies have examined the relationship between leadership styles or approaches and safety performance as one of the indicators of safety promotion. The present systematic review examines the relationship between different leadership styles and the safety performance of employees in healthcare facilities to provide a better understanding of the positive or negative effects of leadership on safety and to suggest strategies for improving safety performance in healthcare facilities.
Material and Methods: A search was conducted in Scopus, PubMed, and Web of Science (ISI) databases. Keywords related to leadership, safety performance, and healthcare employees were used. Studies published up to the end of 2024 were identified and reviewed in accordance with PRISMA guidelines.
Results: Nineteen relevant papers were selected and included in the study. During the review of studies, eleven leadership styles or approaches were identified in relation to safety performance in various healthcare facilities. These included transformational leadership, leader-member exchange leadership, leader safety priority communication and feedback, ethical leadership, empowering leadership, inconsistent and destructive leadership, transactional leadership, task-oriented leadership, authentic leadership, safety leadership, and servant leadership. All leadership styles except for inconsistent and destructive leadership had a direct or indirect positive effect on safety performance. Also, the largest number of studies (n=4) focused on transformational leadership style and leader-member exchange leadership.
Conclusion: The selection of appropriate leadership styles can contribute to enhanced safety, a reduction in occupational incidents, and improving service quality in healthcare settings. The findings of this study highlight the importance of developing effective leadership styles and strengthening appropriate managerial approaches to improve safety in healthcare facilities.
Mostafa Jafarizaveh, Ali Jafari, Mahdi Jafari Nodoushan, Fatemeh Chambari, Farideh Golbabaei,
Volume 15, Issue 4 (12-2025)
Abstract
Introduction: Climate change is a major global challenge, strongly influencing the Wet Bulb Globe Temperature (WBGT) index and heat stress among steel industry workers. This study evaluates the impact of geographical location and climate change on occupational heat stress exposure in Iran’s steel sector.
Material and Methods: This qualitative-analytical study used data from the SABA system and the Iranian Occupational Heat Stress Atlas. Information on steel industries, their distribution, and production capacities across eight climate zones was extracted. WBGT measurements were collected in collaboration with industrial units in different zones. Data analysis was performed using ArcGIS and SPSS. The effects of climate change on heat stress were assessed for three future horizons: 2040, 2060, and 2080.
Results: The findings revealed that climate zones G1 (eastern, southeastern, and desert regions) and G4 (Persian Gulf coastal provinces including Hormozgan, Bushehr, Fars, and Khuzestan), which host the highest steel production capacities, are exposed to the highest levels of heat stress (WBGT index) and water resource scarcity. WBGT values in zones G4 and G6 (Gilan province) exceeded permissible limits, whereas zones G2 (including North Khorasan, Razavi Khorasan, Tehran, Alborz, Qazvin, Hamedan, Markazi, and Chaharmahal-Bakhtiari), G5 (Kurdistan, Kermanshah, Lorestan), and G7 (Ilam, Kohgiluyeh and Boyer-Ahmad) showed the lowest WBGT levels. Considering projected temperature increases in the three future horizons and the acceptable correlation coefficient (0.40) between annual daytime temperature and WBGT index per climate zone, predicted temperature changes may lead to increased WBGT levels, particularly in zones G3, G6, and G8.
Conclusion: Given climate projections and the spatial distribution of steel industries, it is essential to develop climate-responsive policies, implement sustainable water resource management, and reconsider the siting of steel production units. These measures can enhance the resilience of Iran’s steel industry against future climate change and mitigate occupational health and environmental risks.
Vida Rezaei-Hachesu, Ali Jafari, Shadi Naderyan Fe’li,
Volume 15, Issue 4 (12-2025)
Abstract
Introduction: Occupational noise is considered as an emerging risk factor for type 2 diabetes. Although previous studies have mainly examined the auditory outcomes of noise exposure and estimated the relative risk of diabetes, there is insufficient evidence to estimate the prevalence of type 2 diabetes in Workers exposed to occupational noise. The present study aimed to conduct a systematic review and meta-analysis of the pooled prevalence of type 2 diabetes in workers exposed to occupational noise.
Material and Methods: In this systematic review and meta-analysis, the Web of Science, Scopus, Medline (PubMed) databases and Google Scholar engine were searched up to May 2025. The quality of studies was assessed using the Newcastle-Ottawa scale. The pooled prevalence was estimated using the DerSimonian and Laird random effects model, and heterogeneity was assessed using the I² index. The pooled prevalence was reported in subgroups based on the method of diabetes diagnosis and type of study.
Results: Out of 1,193 initially identified studies, 14 studies with a total of 94,975 participants were included in the systematic review and meta-analysis. The pooled prevalence of type 2 diabetes among individuals exposed to occupational noise was estimated at 5.91% (95% CI: 4.85%–6.98%). Significant statistical heterogeneity was observed among studies (I² = 98%, p < 0.001). The subgroup analysis indicated that the prevalence of diabetes in studies based on clinical or paraclinical diagnostics was higher than in studies based on self-report (7.31% and 3.73%, respectively). Moreover, the prevalence of diabetes in cross-sectional studies was higher than in cohort studies (6.45% and 5.67%, respectively).
Conclusion: The findings indicated a moderate prevalence of diabetes among people exposed to occupational noise. This prevalence was based on preliminary studies with an acceptable level of quality. The findings highlight the importance of recognizing metabolic consequences of occupational noise exposure alongside its well-known auditory effects.
