Showing 14 results for Absorption
, , , , , , ,
Volume 2, Issue 3 (12-2012)
Abstract
Introduction: Exposure to respirable fraction of cement dust and its crystalline silica content is the most important occupational risk factor in cement industries requiring more evaluation and monitoring. This study aimed to assess exposure to crystalline silica and cement dust among workers of a cement industry in Saveh city, Iran.
.
Material and Method: In this cross-sectional study, 62 samples of respirable dust were collected from breathing zone of the workers in different sections of factory. Determination of respirable fraction of cement dust concentrations carried out using gravimetric method according to the NIOSH method no. 0600. Visible absorption spectrophotometry was used according to the NIOSH method no. 7601 to determine crystalline silica content of respirable dust samples.
.
Result: The highest exposure concentrations to respirable fraction of cement dust was observed in the Raw Mill and Cement Mill, and the lowest exposure in Administrative Department and Kiln the range of workers exposure in the production sites were 1.77 to 18.89 mg/m3. The range of workers exposure to the crystalline silica in the production sites was 0.011 to 0.104 mg/m3. The highest and lowest mean of exposures was observed in the raw Mill and cement mill respectively. Occupational exposure to the crystalline silica in 57% of site samples exceeded adjusted TLV recommended by NIOSH and Iranian of Occupational Health Technical Committee (0.05 mg/m3). The average of free SiO2 fraction in whole site samples was 1.17% varying from 0.49% in the cement Mill to 1.53% and 1.7% in crusher and Kiln sections, respectively
.
Conclusion: Levels of exposure to cement respirable dust in all productive sections were significantly higher than the adjusted TLV. However, in administrative and control departments it was lower than the TLV level. Regarding crystalline silica, levels of exposure only in “Raw mill” and “kiln” were significantly higher than the adjusted TLV. Highest exposure concentrations to respirable fraction of cement dust recorded in Raw Mill and cement mill, and exposure to crystalline silica in raw Mill, Crusher and kiln, Therefore, preventive measures should primarily be targeted at these units.
, , ,
Volume 2, Issue 4 (2-2013)
Abstract
Introduction: In the steel industry,air blowers used to supply compressed air are considered as sources of annoying noise. This study aims to acoustics analysis of theairblower workroomand sound source characteristics in order to present noise controlmeasuresinthe steel industry.
.
Material and Method: Measurement of noiselevel and its frequency analysis was performed usingsound levelmetermodelof CASELLA-Cell.450. Distribution of noise level in the investigated workroom in form of noise map was provided using Surfer software. In addition, acoustic analysis of workroom and control room was performed in view point of soundabsorption andinsulation. Redesignofdoor and window of controlroom and installation of soundabsorbing materialson theceiling of the workroom were proposed and the efficiency of these interventionswasestimated.
.
Result: The totalsound pressurelevelin the blower workroom was 95.4 dB(L) and the dominant frequency was 2000Hz. Sound pressure level inside the room control was 80.1dB(A). The average absorption coefficient and reverberation time in the blower workroom was estimated equal to 0.082 Sab.m2 and 3.9 seconds respectively. These value in control room was 0.04 Sab.m2 and 3/4 seconds respectively. In control room, sound transmission loss between the two parts of the wall dividing was 13.7 dB(A). The average of noise dose in blower operators was 230%. With the installation of sound absorber on ceiling of workroom, average of absorption coefficient can increase to 0.33 Sab.m2 and sound transmission loss of the new designed door and window was estimated equal to 20dB.
.
Conclusion: The main cause of noise leakage in the control room was insufficient insulation properties of door and windows. By replacing the door and window and installation of sound absorbing on ceiling of workroom, the noise dose can reduce to 49.6%. New Improved door and window of control room can reduce noise dose to 69.65% solely.
M. Osanloo, H. Shirkhanloo, O. Qorban Dadrass,
Volume 4, Issue 1 (5-2014)
Abstract
Introduction: Mercury is one of the toxic metals that damages the nervous system and kidneys. Therefore, monitoring of mercury vapors in the environments is essential.
.
Material and Method: A new adsorbent was made from silver nanoparticles on a bed of quartz. The nano-adsorbent was capable for sampling of the trace amounts of mercury vapor from air. In this study, the required mercury vapor was generate by hydride generation atomic absorption spectrometry and the necessary analysis was performed by cold vapor atomic absorption spectrometry.
.
Results: Mercury vapors in the Stationary phase, were concentrated as much as 2300 times (Atomic absorption detection limit was 1.15 microgram per liter of air). Thus by this stationary phase, the trace amounts of mercury vapors can be detected up to 0.5 nano gram per liter of air. The detected value of the presented method is 200 times lower than the occupational safety and health administration (OSHA) standards for mercury vapors. Heater accessory at the temperature of 245 °C was used for thermal desorption of mercury from nano silver adsorbent. Optimal time of desorption was obtained 150 seconds and the Repeatability of the method was 58 times. The mercury vapors absorbed on nano silver adsorbent could be maintained at 80 days at the room temperature (25 °C).
.
Conclusion: The presented adsorbent is very useful for sampling of the trace amounts of mercury vapors from air. Moreover, it can be regenerated easily is suitable or sampling at 25 to 70 °C. Due to oxidation of silver and reduction in uptake of nanoparticles, oven temperature of 245 °C is used for the recovery of metallic silver. Low amount of adsorbent, high absorbency, high repeatability for sampling, low cost and high accuracy are of the advantages of the presented method.
R. Abedinloo, S. J. Shahtaheri, R. Moradi, R. Divani, K. Azam,
Volume 5, Issue 3 (9-2015)
Abstract
Introduction: Polycyclic Aromatic Hydrocarbons (PAHs) belong to one of the groups of persistent organic pollutants (POPs) which are the result of incomplete combustion of organic materials, volcanic eruptions and forest and agricultural fields’ fires in the environment. However, human factors are main source of these pollutions. Nowadays, these compounds are among the main concerns related to the pollutants which, can easily enter into the land and water systems. Absorption of aromatic hydrocarbons and poly-aromatic molecules on the surfaces of carbon nano-tubes (CNTs) have increased in recent years. In this study, absorption of phenanthrene (as a representative of aromatic hydrocarbons groups) on multi-walled carbon nano-tubes was investigated in organic environment.
.
Material and Method: All experiments were performed in a laboratory environment with a temperature of 24±2.Different variables including the type of solvent, solvent volume, pH of the environment, the absorption time of optimal phenanthrene concentration, and the highest removal efficiency under optimized parameters were obtained. Samples were analyzed using HPLC.
.
Result: Findings showed that methanol with the volume of 10 ml, and the absorption time of 1.5 hours and 1.3 ppm concentration had the maximum absorption efficiency. Environmental pH had no effect on the absorption efficiency.
.
Conclusion: Multi-walled carbon nano-tubes have high absorption capacity for the absorption of phenanthrene. Moreover, in an organic environment, the level of phenanthrene absorption on multi-walled carbon nano-adsorbent was more than 90% and according to the material used was 92%. Day-to-day and within-day reproducibility confirmed the mentioned results.
Roohalah Hajizadeh, Ali Khavanin, Ahmad Jonidi Jafari, Mohammad Barmar, Somayeh Farhang Dehghan,
Volume 9, Issue 4 (12-2019)
Abstract
Introduction: Nowadays multiple techniques have been developed to noise control. One the most important way is the control based on sound absorption and insulation. The purpose of current study was to improve the acoustic properties of soft polyurethane foam regarding combined sound absorption and insulation characteristics.
Materials and Methods: Polyacrylonitrile and polyvinylidine fluoride nanofibers are fabricated using solution electrospinning technique. Nano-clay particles (montmorillonite, 1-2 nm in diameter) were purchased from Sigma-Aldrich, Inc. Experimental design was prepared using Design-Expert ver.7 software. The 50 samples of nanocomposites were fabricated on the basis of experimental run. The measurement of sound transmission loss and the absorption coefficient was conducted using BSWA SW477 550005 Impedance Tubes according to the standard ASTM E2611-09 and ISO10534-2, techniques. Response surface methodology (RSM) with central composite design (CCD) was applied to optimize the conditions to produce nanocomposites for each frequency range.
Results: The polymer nanocomposites had the higher combined sound transmission loss and the absorption coefficient than pure polyurethane foam. Their combined transmission loss and the absorption coefficient in the low, middle and high frequency range was 02.02, 1.91 and 2.53 times higher than the pure polymer. The combined transmission loss and the absorption coefficient in all frequency ranges have been increased by increasing the thickness of the composites and air gap. At a thickness of 2 cm, the combined composites, sound transmission loss and the absorption coefficient increased with the increase of content of both nanofibers. The highest combined transmission loss and the absorption coefficient was observed when mass fraction of nanofibers was in at its maximum level.
Conclusion: This study showed that the adding nano-clay particles, polyacrylonitrile and polyvinylidine fluoride nanofibers to polyurethane foam can lead to increased sound transmission loss and the absorption coefficient. The obtained optimized nanocomposite can be applied to noise control where requiring the absorption as well as reduction of sound transmission.
Marziye Pirani, Mohammad Raza Monazzam, Seyed Qasem Pourjandaghi,
Volume 11, Issue 1 (3-2021)
Abstract
Introduction: Reducing noise pollution has become an essential issue due to the increase in public concern and also social demands for a better lifestyle. Using sound absorption materials is a preferred method to reduce the noise pollution. Undesirable properties of pure polyurethane such as poor absorption of mechanical energy in narrow frequency ranges can be improved by providing polymeric nanocomposites. The main purpose of this study is to synthesize the polyurethane nanocomposite foams in order to improve its acoustic properties.
Material and Methods: At the first steage, pure polyurethane foam was synthesized using the pre-polymer method. Afterwards, nanocomposite foams were synthesized with different mass fractions of Nano silica. The cellular morphology of prepared nanocomposite foams was investigated by scanning electron microscopy (SEM (.Utilizing a two-microphone impedance tube, sound absorption coefficient (α) was calculated in the frequency ranges of 100 Hz to 1600 Hz in order to investigate the acoustic properties of the new absorbant.
Results: According to the microscopic investigations, morphology of the cells changed after adding silica nanoparticles. Also, the cell sizes were observed to be decreased by increasing the amount of silica nanoparticles. Furthermore, the acoustic analysis of nanocomposite foams indicated that the sound absorption increased by enhancing the load of silica nanoparticles.
Conclusion: In the current study, the effect of silica nanoparticles additive amount on acoustic properties of the polyurethane-based nanocomposite was investigated. Our findings depicted that the polyurethane-based nanocomposites were able to promote the sound absorption coefficient.
Reza Jafari Nodoushan, Mostafa Azimzadeh, Sahar Bagheri, Arefeh Dehghani Tafti,
Volume 11, Issue 4 (12-2021)
Abstract
Introduction: In recent years tend to use of natural fibers has increased in making sound absorbers. Fiber-based natural materials have low density, low production costs, and are biodegradable.
Material and Methods: In this study, the effect of nanoclay and the behavior of the nanocomposite specimens containing tea waste, polypropylene, and nanoclay in the sound absorption coefficient are investigated.
Results: The results showed the sound absorption coefficient increases by increasing the tea waste weight percent of the polypropylene. 60% increase in tea waste has a special role in the absorption of sound waves at a frequency of 1000 Hz and 2500 to 6300 Hz frequency range as the TW60 N5 sample has the sound absorption coefficient 0.94 and 0.84 in 1000 and 6300 Hz frequencies, respectively. Comparison of the sound absorption coefficient of composite and nanocomposite showed that sound absorptions increase by adding nanoclay to the 5%, at frequencies above 2000 Hz.
Conclusion: Tea waste-based sound absorbers can be used in noise control due to the high acoustic absorption and no harmful effects on human health.
Zahra Hashemi, Mohammad Reza Monazzam,
Volume 12, Issue 2 (6-2022)
Abstract
Introduction: Micro-perforated absorbents are one of the structures that are widely used nowadays. The sound absorption mechanism is performed by viscous energy losses in the cavities on the plate. In this study, the acoustic properties of non-flat perforated panels in oblique angle was investigated in numerical method.
Material and Methods: This paper examined the effect of the surface shape on the micro perforated absorber performance at low frequencies (less than 500 Hz). The three-dimensional finite element method was used to predict the absorption coefficient of this group of adsorbents. Also, the results obtained from the shaped absorbents were compared with the flat micro perforated ones. After validating the numerical results, six different designs were defined as the surface shape of the micro perforated plates in the COMSOL Multiphasic, Ver. 5.3a software
Results: The results reflected the fact that the factor of the surface shape can be used as a contributing factor in lower frequencies. In general, the dented or concave shapes provide better outcomes than other flat designs and shapes and the convex or outward shapes bring the weakest results.
Conclusion: To explain this function, shaping creates a phase difference and angling the sound wave and creates a variable depth behind the micro-perforated plate. It also influences the reflection process which affect the absorption coefficient.
Ehsan Rezaieyan, Ebrahim Taban, Seyyed Bagher Mortazavi, Ali Khavanin, Hasan Asilian, Elham Mahmoudi,
Volume 12, Issue 2 (6-2022)
Abstract
Introduction: Micro perforated panel (MPP) absorbents promise the next generation of sound absorbers as they have significant advantages over other porous adsorbents. In this study, we will investigate the acoustic performance of MPP absorbents made of biodegradable polylactic acid composite reinforced with natural corkwood fibers (PLA/Corkwood) by 3D printing technology.
Material and Methods: First, the effective dimensional characteristics of the parameters were determined, then, all of the samples were fabricated by the Zortrax M200 3D-Printer using the FDM method. The normal incidence sound absorption coefficient of the samples was measured using an acoustic impedance tube according to ISO 10534-2 in the frequency range of 64 to 1600 Hz. Then the effect of four geometric parameters, including hole diameter, panel thickness, perforation ratio, and air gap depth, on the absorption coefficient was studied.
Results: The findings show that the SL-MPP 12 absorbent has the highest average sound absorption coefficient (SACA) with a value of 0.28, so that at a frequency of 804 Hz it has the highest sound absorption equal to 0.91. The parametric study found that as the hole diameter increased, the values of peak adsorption and average absorption coefficient were decreased. Increasing the MPP thickness causes the absorption peak to move towards the lower frequency range. Decreasing the perforation ratio increases the peak absorption values and the average sound absorption, and the frequency with the highest absorption also moves towards the higher frequency range. The resonant frequency also depends on the depth of the air gap behind the screen. Changes in air gap depth from 30 mm to 70 mm reduced the resonant frequency by more than 35%.
Conclusion: Using 3D printing technology, sustainable MPP can be fabricated with more quality and in less time than traditional methods such as mixing and heat pressing.
Zahra Hashemi, Mohammadreza Monazzam Esmailpour, Nafiseh Nasirzadeh, Ehsan Farvaresh, Zahra Beigzadeh, Samaneh Salari,
Volume 12, Issue 4 (12-2022)
Abstract
Introduction: Natural materials are more efficient and attractive than synthetic materials. In this study, the sound absorption behavior by natural kenaf composite and Micro-Perforated Panel (MPP) at low and medium frequency region was investigated.
Material and Methods: Initially, the results of kenaf fibers with a thickness of 10 mm were validated by the Finite Element Method (FEM) based on COMSOL Multiphysics 5.3a. The studied combined panel is consisting kenaf fibers with micro-perforated plates and an air layer. This study examined the varying arrangement of the behind layers of the MPP, the different thickness of the layers, and the structural parameters of MPP. The structure with the best absorption coefficient was chosen for the following stage and was considered constant at each stage.
Results: The arrangement of composite layers indicated a strong direct effect on the sound absorption performance; as we discovered that kenaf fibers behind MPP led to better performance in frequencies below 2500 Hz. In addition to the chamber depth behind the MPP, the material and macroscopic properties of the layers, at the same depth, are also important determinants of the exact point of the resonant frequency. Furthermore, configurations in which air layer depth is more than the absorption layer, with the same diameter (hole) and depth (chamber), maximum resonant absorption peak is achieved.
Conclusion: Low-frequency sounds can be successfully dissipated by combining MP plates with kenaf fibers as reinforcing absorber in combined panel. In general, choosing the optimum structural parameters (Composite panel according to structure A with 0.5 mm hole diameter and 2% perforation percentage) allows a significant absorption at a specific frequency range. In this context, the use of numerical estimation to assess the sound absorption behavior can be meticulously substituted the difficult methods and laboratory costs.
Ali Jafari, Mohammad Reza Monazzam, Ali Khavanin, Maede Lashgari, Seyed Ali Ghoreyshi,
Volume 13, Issue 1 (3-2023)
Abstract
Introduction: Wood-Wool Cement Panels (WWCPs) are environmentally friendly sound absorbers also used as heat, energy, and moisture insulators. WWCPs have suitable mechanical properties due to using Portland cement and wood strands as raw materials. In this study, the acoustic performance of WWCP absorbents will be investigated.
Material and Methods: The mixed raw materials were molded under pressure through a hydraulic press to fabricate the WWCP samples. Samples were demolded after 24 hours. Samples were created with two thicknesses of 2 and 4 cm and three bulk densities of 400, 500, and 600 kg/m3 to examine the impact of thickness and bulk density on the acoustic absorption coefficient. The sound absorption coefficients were determined as a function of frequency for two frequency ranges: low (63-500 Hz) and high (630-6300 Hz).
Results: In the low-frequency range, increasing the thickness from 2 to 4 cm increased the absorption coefficient at 500 Hz by 0.16 and 0.23 for densities of 400 and 500 kg/m3, respectively. Increasing the thickness added an absorption peak and increased the value of these absorption peaks to 0.9 in the high-frequency range. When the bulk density of the 4-cm-thick samples increased from 400 to 600 kg/m3, the low-frequency absorption peak increased by 0.33. In the high-frequency range, the same density change increased the absorption peak by 0.26 for the 2-cm-thick sample.
Conclusion: Increasing the thickness of WWCP improves both its high- and low-frequency acoustic absorption coefficients. In addition, increasing the bulk density to approximately 500 kg/m3 boosts the sound absorption efficiency in both frequency ranges.
Akbar Ahmadi Asour, Mohammadreza Monazzam, Ebrahim Taban, Zahra Hashemi, Somayeh Amininasab,
Volume 13, Issue 3 (9-2023)
Abstract
Introduction: The aim of this study was to investigate the effect of particle size (mesh) on the sound absorption coefficient of the absorbers made from Arundo Donax reed and to determine the optimal mesh for sound absorption.
Material and Methods: After crushing the reed stems in 10, 30, 20, 16, and 40 mesh sizes, they were washed with 5% NaOH. To make the samples 3 and 10 cm in diameter, 10% PVA was used as a binder, and the impedance of the two-channel tube was used according to ISO 10534-2 standard to determine the absorption coefficient. 22 samples of meshes 16 and 20 were made to achieve the optimal mesh based on the optimized RSM method, and the SAA index was used to compare the samples and determine the optimal mesh.
Results: The highest absorption peak was related to meshes 16 and 20 at the frequency of 2500 Hz, which is 0.94 and 0.98 ,respectively. The effect of increasing the thickness and density on the absorption coefficient is evident. The results have shown the effect of increasing the thickness and density on the absorption coefficient in mesh 20 in such a way that by increasing the density from 150 to 250 and the thickness from 10 to 30 mm, the absorption coefficient has increased from 35 to 63.5%. The optimal sample was mesh 20 with a thickness of 30 and a density of 250 kg/m3, which had the highest average absorption (SAA=0.57). The greater distance between the real and imaginary parts of the impedance shows the reactivity of the sample. In mesh 16 this distance is greater, as a result, mesh 16 has more reactivity and correspondingly less absorption.
Conclusion: The role of particle mesh as one of the important and influencing parameters on absorption coefficient has been investigated in this study.
Gholamreza Moradi, Sana Mohammadi, Abdolrasoul Safaiyan, Saeid Ahmadi, Mehrnia Lak,
Volume 14, Issue 1 (3-2024)
Abstract
Introduction: Disturbing noise can cause physical and mental illnesses among workers; for this reason, it is necessary to restrain it, especially in workplaces. Using sound-absorbing materials with suitable acoustic properties has been a growing trend in mitigating noise. This study aimed to improve the acoustic properties of polyurethane foam (PUF) as a sound absorber.
Material and Methods: In the present study, PUF was synthesized with different percentages of clay nanoparticles (0 -1.2 wt.%), and then the Sound Absorption Coefficient (SAC) of the synthesized PUF was measured by the acoustic impedance tube in the frequency range of 63 to 6400 Hz according to the ISIRI 9803 standard without an air gap behind the sample. The morphology of the foam was also investigated by Scanning Electron Microscope (SEM).
Results: The results showed that the addition of clay nanoparticles to PUF improved the sound absorption behavior of the samples, and the best sound absorption behavior was for PUF with 1.2% weight of nanoparticles at low frequencies (500-2600 Hz). This increase in the absorption coefficient can be due to the increase in the number and smaller size of the pores with the increase in the amount of nanoparticles in PUF.
Conclusion: This study illustrates that the incorporation of clay nanoparticles into PUF at varying percentages results in an enhanced absorption coefficient. The presence of clay nanoparticles leads to a reduction in cell size and an increase in the number of pores, consequently enhancing surface friction. The absorption coefficient was observed to increase with the growing concentration of clay nanoparticles in PUF.
Ali Jafari, Mohammad Reza Monazzam Esmaeelpour, Fardin Zandsalimi,
Volume 14, Issue 2 (6-2024)
Abstract
Introduction: A wood-wool cement panel (WWCP) is wood wool combined with Portland cement mortar. This environmentally friendly acoustic material can be used as a thermal insulator and fire-resistance material with desired mechanical properties. This study aimed to determine the mechanism by which WWCP absorbs sound and the effect of production and application parameters on absorption
Material and Methods: The samples were prepared from poplar wood wool and white Portland cement as a binder in two Cement Fiber Ratios (CFR), namely 2:0.7 and 2:0.95, with bulk densities of 400, 500, and 600 Kg/m3 and thicknesses of 2 and 4 cm. Three layers of backing: air, polyurethane foam, and glass wool were examined separately. Acoustic absorption coefficient was measured using an impedance tube based on ISO 10534-2.
Results: The highest increase in the average absorption coefficient due to the increase in thickness was observed for the sample with a density of 400 kg/m3 and CFR = 2: 0.95, equal to 0.3. Increasing the bulk density to 500 kg/m3 for most samples and in the high-frequency range led to rising absorption efficiency. The optimal backing effect was due to the placement of 4 cm of polyurethane foam behind the sample, which in both thicknesses led to an absorption peak with an absorption coefficient higher than 0.95 at frequencies between 400 and 500 Hz. Selected samples showed that painting WWCPs led to a limited drop in absorption coefficients at high frequencies, comparing the before and after painting results with oil-based paints.
Conclusion: Tuning the absorption frequencies of these absorbers can be achieved by altering factors such as the thickness or density. It has been demonstrated that the effects of thickness and bulk density on the sound absorption of WWCP are related to each other. Concerning the CFR values, increasing the density did not significantly affect absorption in the two frequency ranges.
