Shiva Soury, Abdulrahman Bahrami, Saber Alizadeh, Farshid Ghorbani Shahna, Davood Nematollahi,
Volume 10, Issue 2 (5-2020)
Abstract
Introduction: In this study, Zn3(Btc)2 (metal organic framework) sorbent was introduced for sampling of Benzo[a]pyren from the air. The purpose of this study was to develop the sampling and analysis method by needle trap, with no sample preparation step.
Material and method: Zn3(Btc)2 sorbent was electrochemically synthesized and its properties were specified by FTIR, FE-SEM, and PXRD techniques. A glass chamber with a temperature of 120°C was used to make the certain concentration of Benzo[a]pyren. Factors affecting the efficiency of needle trap were evaluated and optimized using a response surface method considering a specific operating interval to achieve the highest efficiency. The performance of the proposed method was also investigated using the real samples.
Results: The highest desorption efficiency of Benzo[a]pyren was obtained when using the needle trap containing Zn3 (Btc)2 sorbent at 379°C and 9 min retention time. No significant reduction was observed in the analyte concentration by maintaining the sampler for 60 days. The limit of detection and limit of quantification of Benzo[a]pyren were obtained 0.01 and 0.03 mg/m3, respectively. The percentage of standard deviation of the measured values of Benzo[a]pyren in diesel exhaust was calculated 4.1%.
Conclusion: The highest desorption efficiency of Benzo[a]pyren was obtained when using the needle trap containing Zn3 (Btc)2 sorbent at 379°C and 9 min retention time. No significant reduction was observed in the analyte concentration by maintaining the sampler for 60 days. The limit of detection and limit of quantification of Benzo[a]pyren were obtained 0.01 and 0.03 mg/m3, respectively. The percentage of standard deviation of the measured values of Benzo[a]pyren in diesel exhaust was calculated 4.1%.
Amir Hossein Khoshakhlagh, Farideh Golbabaei, Mojtaba Beygzadeh, Seyed Jamaleddin Shahtaheri,
Volume 11, Issue 4 (12-2021)
Abstract
Introduction: Toluene is considered as a group of chemical contaminants, causing problems for people’s health. Due to the high rate of evaporation and rapid emission in the surrounding environment, it leads to the exposure of many employees and people at risk and, subsequently, its irreparable effects on their health in different jobs. Therefore, its removal is very important. In the present study, this contaminant was removed using the copper metal-organic framework (MOF) under different operating conditions.
Material and Methods: In this study, the copper MOF was synthesized using the one-pot and in situ method. Physical and morphological properties of the adsorbent were investigated using BET, XRD, FTIR and SEM techniques. The efficiency of the adsorbent in removing toluene from the air stream under the dynamic adsorption system was investigated by examining the effect of the variables of adsorbent mass, pollutant concentration and humidity. Isotherm, thermodynamics and kinetics equations were used to evaluate the data.
Results: The results of experiments determining the properties of the metal-organic framework showed the formation of pure Cu-BDC crystals with mean and particle size distribution of 1.95 nm. The specific surface area calculated by the BET method for the mentioned sample was 686 m2 g-1 and the total volume of structural pores was 0.335 g3 cm3. The presence of micropores increased the dynamic adsorption capacity of toluene. The findings follow the Langmuir isotherm model and the Pseudo-second order kinetic model. Based on the results of thermodynamic studies, entropy change (ΔS°) and enthalpy change (ΔH°) were equal to -0.44 kJ mol-1 K-1 and -15.67 kJ mol-1, respectively. Gibbs free energy change (ΔG°) was also calculated negatively, indicating that the adsorption process was spontaneous and exothermic. The regeneration of the adsorbent was 77% after three cycles.
Conclusion: According to the results of this study, the microporous copper MOF can be used as a result of cheapness, high access, high adsorption capacity and appropriate regeneration rate in different operating conditions for adsorption of toluene.
