Journal of Health and Safety at Work

---

Introduction: Nowadays, in many different fields of chemical agents several experimental researches is being done on volatile organic compounds using gas chromatography, which is time consuming and expensive methods. Photo ionization detector as an alternative method is used by researchers in this field. This feasibility study was conducted to replace the photo ionization detector with gas chromatography.

.

Material and Method: In this study, after making pre-determined concentrations of Xylene, the results of measurements using photo ionization detector and reference method were compared. This comparison was done in 4 humidity levels and 3 concentration ranges.

.

Result: The results showed significant differences in photo ionization detector readout and the reference method. However correlation coefficient of two methods were more than 0.99 in all cases regardless of the humidity rate.

.

Conclusion: Although the results obtained by the photo ionization detector are different from those extracted from the reference method in the current study, due to linear response of the method correlation coefficient was at good level. Consequently, in case of studying concentration changes in a research, this alternative method would be applicable, otherwise calibration of the photo ionization detector with the target material is recommended.

---

Introduction: Job satisfaction of nurses hasalwaysbeenconcernedin hospitals. It influences the quality of services offered by the nurses. Many nurses leave their job mainly due to the lack ofjob satisfaction.Different factors including the health and safety at work influencejob satisfaction. Thisstudy aimed to evaluate the occupational safety and health status of Khorram Abad’s Shohada hospital and to study its relationship with job satisfaction of nurses there.

.

Material and Method: This descriptive-correlation study was carried out in Khorram Abad’s Shohada hospital. All (239)nurses working in 18wards of the hospital were participated in the study. The required data including individual and job characteristics, occupational safety and healthstatus as well as job satisfaction in terms of hospital nurses were collected using standard questionnaire. Collected data was analyzed with SPSS.19, using Kruskal-Wallis,Mann-Whitney and Spearman correlation tests.

.

Result: The results showed that the occupational safety and health status of the hospital in 4 different studied areas were in a low level (with an average point of 23.2±5.3) from the participant’s point of view. The job satisfaction of nurses was also low (with an average point of 31.8±5.4). The safety and occupational health status of the hospital had a significant relationship with the nurse’s job satisfaction (P=0.001).

.

Conclusion: The job satisfaction of the nurses as well as the occupational safety and health status of the hospital need to be promoted.

---

One of the main goals of all societies whether in developed or developing countries is sustainable development and quality of life improvement. Both of the mentioned fields are known as critical subjects for urban planners, health care systems authorities, organizations and industrial sectors managers. Sustainable development is a global and human-centered approach. Also, ergonomics as a multidisciplinary science has a user center approach in which the quality of life plays a prominent role. The main objective of this article is developing a synergy between ergonomics and sustainability. This research consisted of two parallel phases. The first phase included a review in which two keywords of “ergonomics and sustainability” were considered in PubMed and EBSCO. After following the including and excluding criteria, 12 final articles were assessed. The second phase, was a descriptive study based on questionnaires among 38 participants. According to articles, in-depth evaluation and data gathering throughout questionnaires, it seems that to make a synergy between ergonomics and sustainability especially based on social aspects of both mentioned firms will be ended to effective and feasible planning towards industrial ergonomics and work-related quality of life.  

---

Introduction: Damage to occupational health is one of the major challenges in the industry. Various studies have shown that productivity in industries has a significant relationship with occupational health. In addition, employee’s health in the workplace can be affected by a variety of variables i.e., job stress, job satisfaction, and work in unconventional shifts. Therefore, the purpose of this study was to evaluate the causal relationships of shift work, job stress, job satisfaction with the occupational health level in a petrochemical industry.
Material and Methods: This cross-sectional study was implemented in 2017. The study sample consisted of 20 HSE experts selected using purposeful judgment sampling. A 4×4 matrix questionnaire consisting of four main parameters i.e., shift work, job stress and job satisfaction with occupational health level, was used for data acquisition. Data analysis was done using MATLAB software and Fuzzy DEMATEL method. Also, for each variable, two key values of D+R and D-R were calculated. These values show the degree of interaction and the type of interaction of the variable with other variables, respectively.
Results: Sixty percent of the experts participating in this study were male and 40.0% were female. Only 10.0% of the participants had a PhD degree. In addition, the mean age and the mean work experience of the subjects were 39.64±9.34 and 10.22±7.10 years, respectively. The parameters of shift work and job satisfaction were identified as an effective factor due to the positive values of D-R while occupational health variable with negative value of D-R, was considered as an affected factor. In addition, these results showed that the effect of these parameters on health is different with both direct and indirect mechanisms.
Conclusion: Using the Fuzzy DEMATEL method, our findings indicated that occupational health in the large industries can be influenced by different parameters with different sizes. Considering the interactions among these parameters in health analysis and the affecting factors, therefore, is very important. So, the health level in challenging industrial environment such as petrochemical industries can be affected by shift work as a root cause. This root cause, along with job satisfaction, has a significant effect on increasing stress levels and reducing health levels. Accordingly, any action to increase the health level should focus on improving shift patterns and increasing the level of job satisfaction of employees as a pivotal root and affecting causes on health level.

---

Introduction: Considering the importance of implementing occupational safety and health management systems for the prevention of various diseases in the workplace, as well as determining the notability and role of induction and implementation of occupational health management systems in controlling and reducing COVID-19 outbreak in work environments, as one of the most sensitive and important of society sectors, this study aimed to compare the prevalence of Covid-19 disease in two groups of industries with and without occupational health management systems and related management risk factors in several industries, in Iran.
Material and Methods: This cross-sectional study was performed in May 2020 during the outbreak of coronavirus in some industries under Shahid Beheshti University of Medical Sciences’ supervision. During the present study, 70 industries included 24 industries active in chemical products, 6 industries of automotive parts manufacturing, 14 industries of home appliance manufacturing, 16 industries of health and cosmetics products, 4 industries of metal products, and six service companies were studied. The studied population included two industries with an occupational health management system (33 industries) and industries without an occupational health management system (37 industries). In this study, a checklist was designed to collect study data based on the requirements and parameters of occupational health management systems, as well as information related to infectious diseases such as COVID-19, which included information on COVID-19 disease in two groups of studied industry, occupational medicine, biological hazards risk management, occupational health information management system, training, and employee participation, as well as the management parameters of COVID-19 outbreak. Statistical analysis of the study data was performed using the Chi-square test and Fisher’s exact test by SPSS. 23 software.
Results: The number of workers working in the two groups of industries with and without occupational health management systems was 673 and 708, respectively. Among 33 industries with occupational health management systems, 12.1% industries had health, safety, and environment management system (HSE-MS), 66.7% industries had OHSAS 18001:2007 standard, and 21.2% industries also had ISO 45001:2018 certification. It was found that the prevalence of Covid-19 disease in those industries without occupational health management systems was significantly higher (p <0.05). It has been found that Covid-19 outbreak in industries without occupational health management systems was significantly higher (p<0.05). The findings also showed that there was a significant difference between the parameters of occupational medicine, risk management of biological hazards, occupational health information management system, training and employee participation, as well as the management parameters of COVID-19 disease in the two groups of studied industries (p<0.05).
Conclusion: The findings of the present study indicated that there was a significant relationship between the scores of occupational medicine parameters and occupational health information management system, risk management of biological hazards, training and employee participation, management of COVID-19 and finally the prevalence of the disease among industries with or without occupational health management system. So, implementation and establishment of occupational health management systems can be an effective step in reducing the prevalence of viral and infectious diseases such as COVID-19.

---

Introduction: Considering the importance of identifying and tracing primary sources of Covid-19 crisis in infection control, this study was carried out with the aim of identifying the occupational tasks effective in transmitting Covid-19 in the event of death of a female staff in medical record unit in Shafa Takestan Hospital (Qazvin Province).
Material and Methods: This case study was performed on the death of a 26-year-old married woman working in the medical records department of Shafa Takestan Hospital in March 2019. After identifying and completing the tasks, hazards analysis was performed and finally, various tasks and amount of the Covid-19 sources were determined.
Results: Covid-19 risk sources are classified into three groups of human resources with 51 cases (38.06%), office tools and equipment with 46 cases (34.33%) and paper with 37 cases (27.61%). Four tasks were identified as major tasks with a 59.90% of the total number of COVID-19 risk sources. In this study, two critical tasks were determined with the titles of “reply to requests of forensic medicine and insurance” and “reviewing patients’ surgical reports” that contained a total of 39.06% of the Covid-19 sources.
Conclusion: The results showed that the human resources in two major tasks were the most critical sources of Covid-19. So, the control of these critical tasks is of special importance. The results also showed that it is necessary to transfer the special and unusual tasks to the time after the crisis, in order to reduce the sources of Covid-19 contamination.

---

Introduction: The study of noise has always been of interest to occupational health professionals as a harmful physical factor in the workplace. However, the psychological and psychoacoustic aspects of noise in the workplace have been less studied. This study has dealt with different colors of noise and their applications in psychoacoustics.
Material and Methods: This review study was conducted by searching the databases of Google Scholar, ProQuest, Science Direct, PubMed, and Scopus to extract the articles related to the research subject within a 50-year interval from 1970 to 2020.
Results: Based on the results of the present study, colored noises and white noise seem to have the potential to be used as acoustic stimuli to improve the sleep of employees, especially shift workers, to improve memory and attention, especially in jobs that require high care and attention. Colored noise and white noise have potential applications to improve cognitive function in different occupations to reduce the activity of the sympathetic nervous system and anxiety and stress, especially in jobs with high job stress. Also, these noises are helpful for people’s privacy, especially in the open workplace, for noise masking and noise control purposes, as well as for medicine and treatment of disorders such as tinnitus, ADHD, and hyperacusis.
Conclusion: Paying attention to the colors of noise and their psychoacoustic impacts shows us that the noise impacts are not limited to their undesirable and damaging effects. Instead, their positive and applied aspects should also note. Familiarity with such aspects and their introduction can identify the existing information gaps in this field and pave the way to fill them.

---

Introduction: Strategic management involves determining the organization’s direction, preparing a strategic vision and mission statement, and providing the basis for growth, profitability, and production. It also includes the inclusion of employee safety and health programs throughout the organization. The existence of a strategic plan for the scientific and practical strengthening of occupational health and safety is one of the country’s academic and industrial priorities. The purpose of this study is to present a strategic plan for developing the specialized field of occupational health and safety engineering in Iran.
Material and Methods: The current study is a collaborative action research study that was conducted in 2021. The strategic planning committee consisted of 20 professors, experts, and doctoral students. Over the course of 14 weeks, they held regular weekly meetings, collected information from inside and outside the organization, analyzed the organization’s internal and external environment, and identified its strengths, weaknesses, opportunities, and threats. Based on this analysis, the committee determined the organization’s mission, perspective, values, and general and specific goals for 2021-2024. They also identified the necessary measures to achieve these goals and developed an operational plan to improve the performance of the specialized field of occupational health and safety.
Results: Conducting this applied research led to the strategy of internal and external analysis of the specialized OHS field, determining the direction of the basic strategy, mission, perspective, values, and general goals. Finally, seven specific goals and 286 actions were determined to improve the performance of OHS. The SWOT analysis of OHS’s internal and external environment identified 27 strengths, seven weaknesses, 26 opportunities, and 12 threats. According to the results of the SWOT matrix, the strategic position of the OHS field is to implement preventive strategies and maintain existing conditions.
Conclusion: This plan aligns with the 4-year OHS plan. In developing the program, attention has been paid to the documents and policies of upstream organizations. The strategic position of occupational health and safety engineering is a prudent strategy. In this situation, strategies for maintaining existing conditions can be applied. Therefore, it is suggested to reduce the weaknesses of OHS as much as possible and increase its strategic capabilities by focusing on prudent strategies. From the second year of implementing the strategic plan, the OHS field can gradually focus on developing activities.

---

Introduction: To ensure employee safety and health, it is crucial to choose and use personal protective equipment correctly. An investigation of the respiratory and hearing protection equipment used in the industries of Tehran was conducted in the present study.
Material and Methods: This study was a descriptive-analytical study conducted in 2023 on 400 occupational health and safety experts in Tehran province. A researcher-made checklist and questionnaire (physical and online versions) were used to determine the criteria that are considered when selecting protective equipment. Statistical analysis and graphing were performed using SPSS-v21 and Excel-2016.
Results: Participants had an average age of 38.66 and an average work experience of 11.78 years. The participants reported 48.3% and 47.7% disapproval of the quality and 42.5% and 39.5% disapproval respectively of the quantity of respiratory and hearing protection equipment available in their industrial units. In addition, 56.3% of them admitted that they have no responsibility for providing or approving the equipment in their workplace. Overall, 27 and 29 criteria were mentioned by study participants pertaining to respiratory and hearing protection equipment, respectively. In the identified criteria, the frequency distribution ranged from 0.3% to 38%.
Conclusion: A high rate of expert dissatisfaction with protective equipment and a low frequency of most of the criteria mentioned indicates that industries aren’t paying much attention to the issue of choosing the right respiratory and hearing protection equipment. To improve the situation, more investigation is needed and practical and operational solutions will be provided. This study highlights the importance of proper selection and use of personal protective equipment in ensuring the safety and health of employees.

---

Introduction: The purpose of occupational health is to maintain and improve the health of employees and improve their physical, mental and social well-being through the prevention, control and elimination of occupational hazards. It is necessary to integrate educational, research and health service activities to prevent and control potential occupational health hazards in the community. This study aimed to develop a Joint Comprehensive Plan Of Action (JCPOA) for occupational health at Tehran University of Medical Sciences (TUMS).
Material and Methods: In this participatory action research, a strategic planning committee was established, whose members were professors of the occupational health department in the school of public health and managers of the occupational health department in the health deputy of TUMS. The strategic planning committee carried out a strategic evaluation of the internal and external environments of both occupational health deprtments of TUMS and identified the strengths, weaknesses, opportunities and threats. Then, the strategic direction of JCPOA including the vision, mission, values, goals and objectives was determined. Also, the strategies and actions to achieve the goals and objectives were identified. Finally, the action plan to achieve these objectives was developed.
Results: This applied research led to the strategic evaluation of the internal and external environments of the occupational health depratment of the School of Public Health and the occupational health depratment of the Health deputy of TUMS, determining the strategic direction, and finally, developing an action plan to achieve the goals and objectives.
Conclusion: The JCPOA for occupational health was developed using a collaborative and systemic approach. The proper implementation of this plan can lead to the improvement of occupational health indicators in the community. Cooperation between university and industry is necessary for the sustainable development of society.